Search:

Type: Posts; User: racer69

Page 1 of 8 1 2 3 4

Search: Search took 0.62 seconds.

  1. Thread: Starters?

    by racer69
    Replies
    23
    Views
    8,676

    Running a shut-off in line? I am one who will...

    Running a shut-off in line? I am one who will never run a separate ford solenoid. It is only another place for voltage or amp drop. No matter what your starters solenoid still has to kick in. Just...
  2. Replies
    6
    Views
    34,350

    Your best option is to build some small tabs that...

    Your best option is to build some small tabs that you can cut and tack in place. Use a bump steer gauge setup and cycle it. watch your caster and camber gains/changes. Try many different locations...
  3. Thread: No activity

    by racer69
    Replies
    0
    Views
    61,368

    No activity

    Is anyone on here dealing with asphalt lates? I cross sides from time to time and may need some help with 2 late models Im crew chief on.
  4. Replies
    5
    Views
    4,892

    Have full balancer, cover and timing setup if ya...

    Have full balancer, cover and timing setup if ya wanna try it
  5. Replies
    3
    Views
    45,970

    ^^^ yep! Line up left side and get your new...

    ^^^ yep! Line up left side and get your new measurements.
  6. Replies
    5
    Views
    6,825

    #1 yes #2 yes #3 not small. That side air is...

    #1 yes
    #2 yes
    #3 not small. That side air is important.
    #4 yes
    #5Very yes.
    I used to be one of those (not going fast enough to matter) guys. Its far from true. But dont slow down on suspension....
  7. Replies
    31
    Views
    4,298

    Most of us here are too Kiwi. State by state...

    Most of us here are too Kiwi. State by state orders. Hope y'all are safe as well. My track promoter has the virus. My first experience with those 16Vs was back in the summer. Wow. Working with...
  8. Replies
    6
    Views
    4,293

    Mr. Kennedy Im building a modlite thats 3 link....

    Mr. Kennedy Im building a modlite thats 3 link. That bunch are pretty far behind. I had to redesign whole rear suspension on this thing. Most are running a long solid upper on the right side. Some...
  9. Still have?

    Still have?
  10. Thread: Engine problem

    by racer69
    Replies
    17
    Views
    6,550

    Older optimas=great. Newer ones=junk. I was...

    Older optimas=great. Newer ones=junk. I was selling them for a while. Ive had enough. Never again.
  11. Replies
    6
    Views
    1,915

    Billy

    Was it Lainhart?
  12. Replies
    7
    Views
    3,364

    Yes we have rear jacks and screw cup on front. I...

    Yes we have rear jacks and screw cup on front. I searched for hours and finally found that info from you Stock car. Post was old so Im glad to see its still holding lol. Thanks guys. Thats where I...
  13. Thread: Seats

    by racer69
    Replies
    13
    Views
    2,209

    Im with yall on roof height. I sold my last car...

    Im with yall on roof height. I sold my last car and went new solely because of halo height.
  14. Replies
    7
    Views
    4,146

    Thank you. Much better answer than mine!

    Thank you. Much better answer than mine!
  15. Replies
    7
    Views
    4,146

    You shouldn't have to. However some builders take...

    You shouldn't have to. However some builders take it a few steps further and do some handwork.
  16. Replies
    7
    Views
    3,364

    Metric Ride Heights

    Whats good ride heights for a metric car these days. Been a long time since I set one up. Car has extra angle in LR lower, uses big car spindles, and everything else is stock. Running on 1/4 to 3/8...
  17. Thread: Sell out

    by racer69
    Replies
    1
    Views
    1,033

    Where are you located?

    Where are you located?
  18. Replies
    8
    Views
    1,302

    Find someone with a bert bell with both patterns...

    Find someone with a bert bell with both patterns on it. Set it on your chevy plate and mark the ford holes. Drill plate. Done.
  19. Thread: oil pump?

    by racer69
    Replies
    3
    Views
    970

    I use a stud on most of mine. You do have to be...

    I use a stud on most of mine. You do have to be careful of length on some caps. I had one that would have bottomed threads out on the bearing! Other than that I have had no issues.
  20. Replies
    5
    Views
    1,714

    I know a certain engine builder who is sponsored...

    I know a certain engine builder who is sponsored by E3. Little secret....Runs NGK or Autolites in his race motors. Shhhhh!
  21. Replies
    4
    Views
    5,304

    That was a rough ride!!!

    That was a rough ride!!!
  22. Thread: grain scales

    by racer69
    Replies
    1
    Views
    981

    Interested. Can send pic to 812-572 6738?

    Interested. Can send pic to 812-572 6738?
  23. Replies
    46
    Views
    16,140

    One thing that will help is getting in a good...

    One thing that will help is getting in a good race with the best guys. With help from HEAVY DUTY and others I was getting better. Making the car right. One night I made the feature with some of the...
  24. Replies
    12
    Views
    4,027

    Another vote for Micro Armor. Amazing stuff....

    Another vote for Micro Armor. Amazing stuff. Holds up great in my 200 lap-a-race asphalt car.
  25. Thread: Kirkey LW Seat

    by racer69
    Replies
    3
    Views
    974

    All good. I bought one saturday at the track for...

    All good. I bought one saturday at the track for 50!
Results 1 to 25 of 193
Page 1 of 8 1 2 3 4

All times are GMT -5. The time now is 09:58 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.