Search:

Type: Posts; User: Renegade Cust Susp

Page 1 of 7 1 2 3 4

Search: Search took 0.46 seconds.

  1. Replies
    32
    Views
    12,192

    The over rails are higher and rr rail is inset...

    The over rails are higher and rr rail is inset farther to give more clearance for spring movement and tire movement, main frame rails are in the same place, rails over the rear ended are higher
  2. Spoiler angle

    Heard a convo at PRI that a certain mfg had done wind tunnel testing and found that 90–70* there was enough downforce to be used as a tuning tool, from 70* to 0 there was little to no usable...
  3. Bump for edit

    Bump for edit
  4. Replies
    15
    Views
    3,387

    Had a similar winter project last winter...

    Had a similar winter project last winter
    https://www.flickr.com/photos/185301009@N08/albums/72157711544228213
  5. Replies
    20
    Views
    4,632

    Engine is a gb2000 Brodix head with a 4/7 swap...

    Engine is a gb2000 Brodix head with a 4/7 swap cam, we tried to tune it down with not matching intake so it’s a little smaller and on the engine dyno it made 796hp and right about 670-680lbft don’t...
  6. Replies
    20
    Views
    4,632

    Engines

    Had a 13* 390 cu in, that made way too much most of the time. Anytime the track would blow Black it had to be toned down. Most nights on 3/8ths tracks it was on two barrels
  7. Replies
    27
    Views
    8,078

    Justadddirt- I see what your doing here... 😂

    Justadddirt- I see what your doing here... 😂
  8. 2016 Bandit less than 30nights since new

    Sold..........
  9. Replies
    16
    Views
    2,300

    Excessive LS bar angle will cause this too

    Excessive LS bar angle will cause this too
  10. Replies
    3
    Views
    798

    Can be done, and it can be fast, but yes a std...

    Can be done, and it can be fast, but yes a std 9010 is not enough to do this correctly
  11. Replies
    4
    Views
    919

    Contact Carolina Test Works.... they are the guys...

    Contact Carolina Test Works.... they are the guys that were formerly with Roehrig and now have moved out on there own since Roehrig was bought out by MTS. From my conversation with them at PRI they...
  12. Replies
    4
    Views
    1,484

    CSI or Momentum suspension both out of...

    CSI or Momentum suspension both out of Indy/Brownsburg area
  13. Replies
    1
    Views
    1,567

    ETG limiter

    Pm sent about setting limiter
  14. Replies
    3
    Views
    1,618

    http://www.seegysraceproducts.com/page16.html ...

    http://www.seegysraceproducts.com/page16.html

    Pics are in a mod but same principle applies
  15. Replies
    18
    Views
    3,129

    Had an issue with car switch there was a small...

    Had an issue with car switch there was a small difference in radiator heights which got us into a little bit of a problem with temp. Raised new one up to match old set up heat issue went away
  16. Replies
    2
    Views
    939

    I am on my third impact vapor and 6th impact...

    I am on my third impact vapor and 6th impact helmet and love them. impact offers more chin jaw line coverage than most helmets. I have crashed them HARD in my time racing sprint cars and modifieds...
  17. Having a good wheelman never hurts the cause...

    Having a good wheelman never hurts the cause either.
  18. Replies
    3
    Views
    1,907

    Location?

    Where are you measuring? Typically we used to run 8" +/- 1/4" measure front lower control arm bolt to ground (that's with nova lowers and pintos)
  19. Replies
    5
    Views
    2,701

    I've seen rules that dictate a minimum but I have...

    I've seen rules that dictate a minimum but I have never seen a rule stating the wheelbase has to be the same/square
  20. Replies
    4
    Views
    2,157

    I always had my best luck in a clamp car with a...

    I always had my best luck in a clamp car with a 500-1000, it's just what I liked may not be for everyone
  21. Replies
    2
    Views
    1,724

    The m60/H is a rr option. A lot of guys out there...

    The m60/H is a rr option. A lot of guys out there only run 26.5"
  22. Replies
    27
    Views
    7,104

    Heavy Duty is Don Adams owner/builder of...

    Heavy Duty is Don Adams owner/builder of Lightning Chassis, you wont meet a nicer guy in racing.
  23. Replies
    10
    Views
    2,459

    The website shows a price in the middle of a...

    The website shows a price in the middle of a description of $899 each
  24. Replies
    32
    Views
    5,827

    In the way that you are using shock (absorber)...

    In the way that you are using shock (absorber) you are correct, technically anything that physically dampens force is a shock.

    Hadn't gotten this in depth into the engineering of the components...
  25. Replies
    32
    Views
    5,827

    Not hard at all as long as the shock components...

    Not hard at all as long as the shock components are robust enough
Results 1 to 25 of 169
Page 1 of 7 1 2 3 4

All times are GMT -5. The time now is 10:13 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.