|
|
Search:
Type: Posts; User: LIS20
Search:
Search took 2.09 seconds.
-
Dinka2 2 you called me this morning -- this is what i have
rayburn “revolutiion” chassis [2011/12]
chassis – never been bent – one small modification in rear for clearance
front:
18 sweet...
-
how do you use your wooden blocks -- i can picture them but not how they are used-- thanks in advance
-
I just lay the wrinkled pannels in the grass and walk over them - helps get most of the wrinkles out - then i use a rubber or deadblow hammer to finish -- do not beat on it -- it will stretch the...
-
I put a line spring in all suction lines
-
Can the blue spindles or rayburn spindles be used on a black front rocket - i would like to raise the front of the car for ground clearance - i saw a spindle where the spindle was about 1/2 inch...
-
I would check with dbr performance and machine 931-724-9201 cconcerning your starter - they have done several for me and have had no problems
-
I was a 43 year old rockie in a super late model - i am now -- the driver i puechased the car from was 6'7" and i put everything back the way he had it -- the problem i had the first night was when i...
-
My trailer has started blowing tires -- tires have been new - proper inflation - have not added more to load - basically dirt late model with tires, tools, and spares -- have looked for contact areas...
-
There is a cj rayburn site that gives two pages of set up information --i have used it for both a rayburn and rocket -- follow this .
-
i use the steel braided lines -- be sure to the springs of all suction lines -- it is good insuance for a collapsed line
-
Thanks for all your help -- found that the battery box hold down bolt nub on the side had worn a hole through the side of the battery and shorted out the starter -- i guess there is a first time for...
-
Situation: High air temper - [98] - very humid - heat index [105] - battery charger indicated full charge
engine: 441 aluminum with appx. 750 hp and 13-1 compression
problem: During feature...
-
WHAT IS THE PURPOSE OF A CHAIN ON THE RIGHT REAR? i HAVE SEEN SEVERAL CARS [SUPER LATE MODELS] WITH THIS AND HAVE GOTTEN SOME REALLY STUPID ANSWERS [EX. IT HELPS WHEN JACKING THE CAR UP]. AND .. HOW...
-
I have used renegade 116 for several years with no problems.
-
Had a problem saturday night - spun in future - could not get car to start either by starter button or by pushing -- car was pushed back to trailer and started right up - using optima red-top battery...
-
What is the housing width for an 09 rocket - the allstate catalogue indicates
62-62 1/4 inches -- what is considered correct and how is this measured -- what effects are there if the measurement is...
-
Can having to much left rear drop cause the car [black front rocket] to carry the left front -- have been told a heaver rr spring [225 to 250] an/or a left front teather will help solve this problem...
-
Does anyone have a clear picture of the teather used on the left front of a rocket or is this a kit available from rocket -- thanks in advance -- happy thanksgiving
-
When using a wheel spacer - ex: 2" on left rear - do you add turns to the spring or not -- i have heard both -- thanks in advance
-
What are the length of the axle tubes ( not axles) on a rocket - i called rocket and they gave me left 26 5/8 and 30 1/8 -- this doesn't seem right to me -- thanks in advance
-
What did they do - what can you do - to calm down the left front hike
-
On the left rear behind shock i have seen mounts that are straight and those that are 45 degrees -- is there any real difference if both have the swivel mount? Ehat would be the best mount for the...
-
are you connected to the correct terminal on the solenoid - i use a "quickcar" solenoid and there is only one terminal -- on the ones with two small terminals use the one on the left as you are...
-
Does setting the rf shock setting to full stiff create a tie-down effect-- ie. Slow the rate of"pop-up" of the shock -- also what is the effect of setting the compression to full stiff have?? I'm...
-
We had a similar problem and completely rewired the ignition system - turned out it was the carb - the primary float for some reason was flooding out the engine causing it to pop and crack coming...
All times are GMT -5. The time now is 01:35 PM.
|
|