Search:

Type: Posts; User: TR32

Search: Search took 0.17 seconds.

  1. Mini Stock plus Roller and spare parts...........

    Mini Stock #32 Race ready minus motor + rolling chassis (no body) and all spare parts. My car ran twice this year at I25 Speedway in Pueblo, Colorado. Chassis is a 74 Ford Pinto, body has been...
  2. Thread: rear weight

    by TR32
    Replies
    26
    Views
    4,583

    Pretty much common knowledge that the trade off...

    Pretty much common knowledge that the trade off for the strength of a 9" is the extra horsepower it takes to turn it. If your worried about breaking the rearend the most you need behind a 4 cyl is an...
  3. Replies
    18
    Views
    2,547

    Pretty much agree with all the posts above. Mine...

    Pretty much agree with all the posts above. Mine is wired with the bottom three wires. Never a bad thing to use the ground wire as long as its done right. I have mine grounded to one of the bolts on...
  4. Replies
    15
    Views
    3,340

    If you're running a tfi distributor you might try...

    If you're running a tfi distributor you might try running some cool air to the tfi module, they tend to run really hot and burn up......I would do the same if running a duraspark setup.....
  5. Thread: Auto trans

    by TR32
    Replies
    2
    Views
    1,010

    Auto trans

    Has anyone tried running an automatic behind the ford 2.3 in a mini stock?
    Just curious since there used in street stocks and modifieds quite a bit.....
  6. Replies
    18
    Views
    3,089

    And the piston kick back springs............

    And the piston kick back springs............
  7. Thread: specs

    by TR32
    Replies
    4
    Views
    1,397

    As usual, excellent info from you Dave!!!!

    As usual, excellent info from you Dave!!!!
  8. Thread: Roller followers

    by TR32
    Replies
    5
    Views
    1,550

    Roller followers

    Dumb question time.
    Can you use roller followers on a non- roller cam?
  9. Replies
    9
    Views
    1,738

    Cam specs

    You need to your cam specs to know what rpm's you should be turning. Also, you should find out what the other racers are using for a final gear ratio. Your final gearing is 6.59 (2.14 x 3.08). If...
  10. Replies
    10
    Views
    2,477

    Sent you a PM Mark.

    Sent you a PM Mark.
  11. Replies
    10
    Views
    2,477

    Isn't 4 lines a bit excessive? I would like to...

    Isn't 4 lines a bit excessive? I would like to hear more about your system though. Does evacuating to the collector free up any hp?
  12. Replies
    10
    Views
    2,477

    Venting the crankcase

    I have seen and ran a block(2.3l) that had the crankcase vent hole plugged. I never had an issue with blow by. I have also ran one with the hole unplugged and had serious blow by through a breather...
  13. Replies
    5
    Views
    1,060

    Have you tried looking for a part number?

    Have you tried looking for a part number?
  14. Replies
    8
    Views
    2,688

    Can't use metric, has to be oem family to...

    Can't use metric, has to be oem family to family.....
  15. Replies
    8
    Views
    2,688

    Disk brakes

    Do you use everything from the escort, bracket, rotor, and caliper?
    Is there any fabricating to do?
Results 1 to 15 of 15

All times are GMT -5. The time now is 10:53 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2020 vBulletin Solutions, Inc. All rights reserved.