|
|
Search:
Type: Posts; User: el paso mod 19
Search:
Search took 1.29 seconds.
-
Interesting, I may try making some when I get a little time. Thanks
-
Thanks Andy, that is the one I was looking for.
-
Thanks, didn't think about Lowe's or Home Depot.
-
I have seen shrinker pliers but can't seem to find who sells them. They look like they are from the "1950" but work really well. They have "duck bill" with about 2-3 indents and you just squeeze...
-
I've been told that Sanders setup, which I'm not sure what he is running, will not be allowed next year. Was told this by a very straight-up friend that always seems to be in the know. Sanders,...
-
Thanks for the reply Charlie. My car reacts to GRT setup changes almost to the "T". I've never done what you suggested, but I will try it next time slicks off.
-
Charlie, so you are raising up the weight of the car for more side bite?
-
I've got a pretty good setup for tacky track, but I stink when track slicks off. I run spring on rear and shock in front on LR and coil over in front on RR. J-bar on left frame set at 4". What...
-
Does both metering blocks have a power valve? Will both probably be blown?
-
I haven't taken carb apart yet, but I think I may have blown a power valve. Put new carb on two races ago. Had problems getting motor fired and it backfired once. Then this last weekend it...
-
Motor doesn't want to pull hard. Ran 602 gear race before and switched to 648 gear last night and increased maybe 50 rpms. Another driver said he had exact same problem a couple weeks ago and...
-
Thanks for the replies. My shocks don't have adjustment knobs for quick changes(lowering compression) so I guess I should just unhook the bottom and leave hanging. I know that when I started taking...
-
I just bought a bottle at Wallyworld. I have a 6 1/2 quart pan, will 8 oz of this be enough? If it does it would be good for 4 oil changes.
-
This is two questions. One, if you are running really aggressive shocks, do most people disconnect them when setting ride heights and scaling? I already slide RR axle out, but I think the shocks...
-
Sorry for the confusion. Thanks, the replies helped me with my decision.
-
Either it's a stupid question, or nobody knows answer, or maybe it is a secret. I guess I'll put it as close to cages as possible and try to get upper mount outside of J-bar frame mount.
-
Where would the ideal placement of a chain eliminator be? Directly above axle tube at ride height or somewhere else. Where would you mount bottom bracket left or right wise. How about upper mount,...
-
OK. Just stripped out drive flange and never really noticed before that it was aluminum. Think I'll order a steel flange.
-
Stripped out RR drive flange. What is your thoughts on steel or aluminum? Does the alum flange save the axle from possibly breaking or is it just a weight deal?
-
Since it isn't getting over on RF, could you possibly have a bent shock on that corner?
-
Groove your tires differently. You may not make the sidewall flex easier but you can make the outer tread flex a lot more by grooving. After all, that is what you're trying to do is get that outer...
-
-
Does it change what the moving of bar does depending if you go from, say, 4 degrees up down to 0 degrees vs going past 0 to a negative degree? Reason I'm asking this is a few weeks ago we ran same...
-
I guess that without the roof it would redirect air flow. Hadn't thought of that, cause we do run an 8" spoiler. We ran two weeks ago with 27 non wing 360 sprints and the track for our main had a...
-
Trying to get a head start on this. We are going to go topless Labor Day weekend. Never ran this way(not sure I really want to). What changes do you make? Seems to me we will be loosing a lot of...
All times are GMT -5. The time now is 08:36 PM.
|
|