Search:

Type: Posts; User: 1195

Page 1 of 2 1 2

Search: Search took 0.37 seconds.

  1. Replies
    3
    Views
    3,746

    I have run .504 lift on 3 different heads without...

    I have run .504 lift on 3 different heads without cutting the guides. Your results may be different.
  2. Thread: tfi wiring

    by 1195
    Replies
    3
    Views
    885

    Use the bottom three. Red Black. Green

    Use the bottom three. Red Black. Green
  3. Thread: Trans gears

    by 1195
    Replies
    1
    Views
    1,248

    1.81,1.97 and 1.99 are the ones I am familiar...

    1.81,1.97 and 1.99 are the ones I am familiar with.
  4. Replies
    12
    Views
    2,562

    FLYIN-9 Just throwing out a couple ideas. You...

    FLYIN-9
    Just throwing out a couple ideas. You said the cam bearings are not "slotted" Do you mean on the outside or inside?
    The improved oiling cam bearings are grooved on the outside and...
  5. Replies
    1
    Views
    1,362

    The early 2.3 had the larger shaft size. 74-82

    The early 2.3 had the larger shaft size. 74-82
  6. Replies
    29
    Views
    6,648

    Does it cool down quickly or slowly when you slow...

    Does it cool down quickly or slowly when you slow the engine RPM down?
    Also check both hoses to see if the spring goes the full length of the hose. It only takes a couple inches with no spring to...
  7. Replies
    29
    Views
    6,648

    Yes the holes need to be plugged.

    Yes the holes need to be plugged.
  8. Replies
    29
    Views
    6,648

    Check to see that the plug is in the back of the...

    Check to see that the plug is in the back of the camshaft. Also if the cam bearings that were installed have the groove around the outside the holes in the tops of the cam towers have to be plugged....
  9. Replies
    9
    Views
    2,233

    M13?? Possibly

    M13?? Possibly
  10. Replies
    10
    Views
    1,852

    Check to see if the bushing the yoke rides in is...

    Check to see if the bushing the yoke rides in is worn. That will cause the seal to leak.
  11. Replies
    5
    Views
    1,291

    FelPro 8993 The Victor Reinz gaskets I have...

    FelPro 8993 The Victor Reinz gaskets I have used suck.
  12. Thread: Cam problem

    by 1195
    Replies
    14
    Views
    1,843

    I have had 2 new cams with new followers that had...

    I have had 2 new cams with new followers that had follower failuer that looked simalier to that.
    Both had correct geometry. I polished the lobe and put a "good" used follower in and ran them for...
  13. Thread: Cam problem

    by 1195
    Replies
    14
    Views
    1,843

    Can you post pictures of the failed followers?

    Can you post pictures of the failed followers?
  14. Replies
    19
    Views
    3,719

    Good job. Have fun.

    Good job. Have fun.
  15. Replies
    19
    Views
    3,719

    Exhaust is 116

    Exhaust is 116
  16. Replies
    19
    Views
    3,719

    Dirtman29 The cam card should also have the...

    Dirtman29
    The cam card should also have the spec's @.050. This is the best way to compare it to other cams.
    229-2046
    Duration 230 @ .050
    IVO 6*BTC IVC 44*ABC
    EVO 50*BBC EVC 0*TDC
    Valve Lift...
  17. Replies
    19
    Views
    3,719

    Dirtman 29 Yes use the regular followers. ...

    Dirtman 29
    Yes use the regular followers. 229-2047 is not a roller cam. I would run it 3 degrees retarded.
    max hp will be between 5500 and 6000 it will run on up above 7000
  18. Replies
    19
    Views
    3,719

    Dirtman 229-2047 is a slider cam. If you are...

    Dirtman
    229-2047 is a slider cam. If you are running it with roller followers it will change the Vale timing.
    I have run this same cam with sliders. It isn't the strongest but does run good. It...
  19. Replies
    1
    Views
    1,212

    Which bearing are you looking for? The pilot...

    Which bearing are you looking for?
    The pilot bearing that goes in the crank.
    The input shaft bearing that goes in the case.
    The pocket bearing (needle) that go between the input and output shaft...
  20. Replies
    1
    Views
    1,352

    http://www.ebay.com/itm/1980-FORD-MUSTANG-POWERTRA...

    http://www.ebay.com/itm/1980-FORD-MUSTANG-POWERTRAIN-Repair-Service-Shop-Manual-DEALERSHIP-OEM-80-BOOK-/160881974477?pt=Motors_Manuals_Literature&hash=item2575501ccd&vxp=mtr
  21. Thread: 2.3 omc

    by 1195
    Replies
    2
    Views
    1,447

    2.3 omc

    Has anyone here tried the 2.3 OMC intake and Rochester carb. on their ministock?
    I have a couple of them but havent ever seen them used on a car.
  22. Replies
    11
    Views
    2,320

    Timing belt stretch?

    Timing belt stretch?
  23. Thread: Fuel consumption

    by 1195
    Replies
    7
    Views
    1,906

    5 lap dash, 12 lap heat, 25 lap Main. 3/8's mile...

    5 lap dash, 12 lap heat, 25 lap Main. 3/8's mile Dirt 4 to 5 gallons.
    We also run a 2.3L Mustang Road Race car (ChumpCar) 5.5 to 6 gallons an hour
  24. Replies
    3
    Views
    1,318

    http://www.4m.net/showthread.php?307689-Seals-for-...

    http://www.4m.net/showthread.php?307689-Seals-for-transmission
  25. Thread: Camshaft help

    by 1195
    Replies
    4
    Views
    986

    http://www.raceeng.com/techsheets/FD-3-6_PDF.pdf

    http://www.raceeng.com/techsheets/FD-3-6_PDF.pdf
Results 1 to 25 of 44
Page 1 of 2 1 2

All times are GMT -5. The time now is 11:12 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.