|
|
Search:
Type: Posts; User: raceman17
Search:
Search took 0.40 seconds.
-
I've had these same set of scales for over 10 years. They work great and always zero out once I remove the car from the pads. I would not hesitate to buy these scales again.
-
You have to drill a hole into the top of the fuel cell and install a bulkhead fitting for your return.
-
On one of my cars I use the clear vinyl to go over the side of my body. I have nerf bars so I dont have to worry about wheel scrubs but it does help with cleaning the mud off the car and my white...
-
Well its hard to say because the throwout bearing travel is based on what type of pressure plate/clutch you are using. You need to have enough travel to disengage the clutch when you press on the...
-
duh... sorry about that. I had a big brain fart. you are not going to be able to push from the good side unless you can machine out something that resembles a pickle fork that will go around the...
-
Did you remove the cross pin before you tried to get the axle out from the other side? If you were using the other straight axle as a push rod to push the other broke end out then you probabaly do...
-
.063-.125" will work fine. You also need to keep in mind that you may have to add a pedal stop to the clutch pedal so you do not over extend the throwout bearing and put to much force on the...
-
.063"-.125" should get you where u need to be.
-
I use the origianl HD camera.
-
I use the gopro hero cam on my cars and I have liked it alot. Gopro.com has them for sale for 129 right now. If you want to see video quality you can find my videos on youtube. Just search for...
-
Add washers to both sides of the nut amd bolt.
-
Go to ebay and search for "7.5 3.90" There are 5 sets listed.
-
What size is your fuel line? Also, how old is your fuel pump? Are you using a stock pump? Also, have you checked your float level in your carb? If could be set too low.
-
In one word HARD! You are going to have to clip the whole back end of the car and replace the rear frame section of the mod with your stock rear frame. Your entire interrior will need to be...
-
Get the R2C. I started running one this year and the first night in the tech shed when we pulled the filter to check the carb the carb bore was spotless. We race on a dusty track too. It was worth...
-
IF the flexplate is on correctly, add another washer to the inside starter bolt. On my current setup I had to add two 3/8" washers to the outside starter bolt to space it in correctly. The total...
-
Your rear springs are too tall. If your weight jacks mount to the stock spring mounts in the rear then a 15" spring will really jack the rear of the car up. You need some shorter rear springs.
-
You get what you pay for. Dont waste your time buying a cheap battery. An optima battery can last for years and give you plenty of power to start your car. You can buy cheap this year and next...
-
I ran a granada for one year when I first got into racing in the late 90's. It was the WORST thing you could ever have on a race track. The front syspension was a PITA to do any adjusting on. ...
-
They are a set of fabricated aluminum vortec head valve covers. They have a cheesey looking insert pressed down into the tube with two half moom bent slots in each insert. Another option would be...
-
I had that problem on my car before. I made and installed a homemade baffle like the one you can buy that attaches to the rocker stud to deflect the oil back down on the valve train and it stopped...
-
I have one on my car and I love it. Its easily to clean and will save you money after several oil changes. When I spin my filter off from the block oil does not go down the sides of the filter like...
-
Any type of wax will work. The easiet thing to use is a birthday candle.
-
The early corvette flywheel 60 or 70s model (153 tooth) is one of the lightest you can get. Autozone sells then for right around 60 or 70 dollars. You might have an issue with the starter though. ...
-
I went though a bout of breaking ears off the saginaw for weeks. I think I busted 4 or 5 cases in a matter of 8 to 10 weeks. Like Jeff mentioned above.. Make sure the surface where the...
All times are GMT -5. The time now is 06:54 AM.
|
|