|
|
Search:
Type: Posts; User: 3dinter
Search:
Search took 1.74 seconds.
-
-
By scales , 842 lr, 765rr, 686 rf, 788 lf..total 3081...guys excuse my terminology....i dont understand wedge and bite, so please if you give a suggestion, dumb it down please.
-
Right rear cannot go in any further the 10" tires on 8" rims will cause the tire to rub frame, etc .......I am less than 100 bite, if you mean the difference between the left and right rear weight by...
-
3081 lb metric, 1 inch offsets on all 4 corners. 10" Hoosier asphalt slicks f-45 on 8" rims, 1000lf, 1100rf, 250lr, 200rr, QA1 shock "weight transfer" package as recommended in their book. Left 52.9,...
-
Im a lil lost on the fix,,,bigger rate spring on r/r ?
-
Can you explain what lowering the carb linkage closer to the pivot point on the pedal does.
-
I have a 3.562 stroker motor i just had built, it has the 487x heads with 2.02 / 1.6 valves and shaved 80 thousandths, bored 40 over with 4 valve relief flattops, 446 / 446 cam, stock steel...
-
Ok, if they were spark plug holes, what prupose does it serve to plug them up since he shaved my heads so much ?
-
parrot69777
I maybe wrong on this,,but i think they were close to the edge of the head, dont quote me on this cause he already put the heads on the block when i got it back from the shop.
2 holes...
-
i might be calling them wrong, but they are about a lil smaller than a pencil is round and there was 2 i think per cylinder.
-
I just got my heads back from the machine shop and they plugged the steam holes.
i can say the heads were a 1.94 when i turned them in, he said the wouldnt clean up so he went to 202 and milled /...
-
i run a stock 7.5 with a 2.56 and a th350 in first gear with a stock 355 and a gm z28 cast iron high rise "cast iron copy of the old aluminum one", stock below plug cast iron exhaust, 4412 holley and...
-
What only 1 answer...you guys must be pissed off racing season is over and are out deer hunting...bahabahbahbahabahaaaa
-
What would you say "in your opinion" is the best weight percents for a dry slick track in a 3000 lb hobby, pure / factory stock on a 1/4 mile, semi banked track ?
Rear % =
Left % =
Cross % =
-
I am going to pose this question and i think based on the area of the country you are from we are going to get different answers based on weather conditions.
What grade of motor oil do you use in...
-
-
i always wanted to try the 10" rims. pm me and ill send you to a few places to see the hoosier in action on 8" rims via video and pics. We run 12 to 15 rf, 10 to 12 lf, 8 to 10 lr, 10 to 12 rr with...
-
Even though Hoosier recommends a 10" rim for these tires, we have to run the F40 and 2045 on a 8" by our rules without a beadlock. do not go lower than 6 psi on them or youll run off the rim without...
-
-
here is our 2012 rules, my bad...not sure where i got 377 max cub's.
ENGINE: Must be stock for the make and model except no 400’s or larger small or big blocks.
All engine components including...
-
I understand completely...but we was legal by the rules all of last year, with the best driver around here and we would get almost lapped...so that obviously told us something and whats the old...
-
are you referring to, what we call asphalt pull-offs down here ? Hoosier f-40 and Hoosier 2045 ?
if so we run them as per the rules on a 8" rim, some places allow beadlock and some place do not on...
-
i run about the same tracks here in Texas, we run a non-locking 350 turbo in first gear in a gm 7.5 metric rear with a 2.56 ring and pinion and we turn 6000 rpm with a z28 cast iron intake, about...
-
I use both a Go Pro Hero and a Flip Cam, Both are HD...i tend to use the flip cam more as of right now due to we just got the Go Pro, Flip Cam is a lil cheaper and has SW for editing that comes with...
-
i actually got it for a swap of some other race car junk....
All times are GMT -5. The time now is 09:50 PM.
|
|