Search:

Type: Posts; User: ace1

Page 1 of 7 1 2 3 4

Search: Search took 0.71 seconds.

  1. Thread: Ball joint

    by ace1
    Replies
    4
    Views
    1,762

    Has anyone ran into an issue with some lower ball...

    Has anyone ran into an issue with some lower ball joint brands with the nut being too big to go between the gussets on the spindle?
    It will fit but you can't get a socket on it. The stud is the...
  2. Replies
    3
    Views
    5,050

    Per the old set up sheets, it has 1/2" spacers on...

    Per the old set up sheets, it has 1/2" spacers on the tie rod ends at the rack. My thoughts are to raise the rack 1/2", leave the spacers out and that won't effect geometry.?? Oil pan is also hitting...
  3. Replies
    3
    Views
    5,050

    Mastersbilt Rack Plate Update ?

    Anyone that has updated a mastersbilt rack plate, How much did it raise the rack. 1/2" or more ?
  4. Replies
    3
    Views
    1,245

    I took measurements from another car and layed...

    I took measurements from another car and layed out those dimensions on mine, then to check myself I dropped a plumb bob off the control arm holes on the rack cross member and and then off my marks on...
  5. Replies
    3
    Views
    1,245

    Mastersbilt cross member help

    I have an 08 Mastersbilt that I need to put a front cross member in. Anyone know the distance between the lower control arm bolt holes? Shouldn't it be the same spacing as where the control arms bolt...
  6. Replies
    9
    Views
    1,761

    I just replaced mine. I had used the ones from...

    I just replaced mine. I had used the ones from autozone, I think is where I got it. I made a puller like the ones being sold. When I inserted the tool it pushed the bushing out so I pulled the tail...
  7. Replies
    1
    Views
    1,005

    I just saw one on ebay. Might be closer to 4.5"....

    I just saw one on ebay. Might be closer to 4.5". ??
  8. Replies
    1
    Views
    1,005

    Bert Output Shaft Spline Length

    I need to know the length of the output shaft splines on the bert 1st gen. slip yoke trans. Does 7 1/4" sound right?
  9. Replies
    2
    Views
    1,836

    I think I'll keep it on what it calls for. Thanks

    I think I'll keep it on what it calls for. Thanks
  10. Replies
    2
    Views
    1,836

    Left Frt. Upper Control Arm Mounting

    I need a left upper control arm for a 08 Mastersbilt. Calls for a 10 1/4". It mounts to the inside of the frame. If I can't find a 10 1/4, would there be any issues using a shorter and mount on the...
  11. Thread: 602 Fuel

    by ace1
    Replies
    2
    Views
    1,562

    E85 is legal as of this year.

    E85 is legal as of this year.
  12. Thread: 602 Fuel

    by ace1
    Replies
    2
    Views
    1,562

    602 Fuel

    What fuel are you running in your 602? I have been using 110 race gas. Is it really any better than pump gas for these motors. I know pump is recommended from factory.
  13. Replies
    0
    Views
    1,633

    Mastersbilt Spindles

    What is the difference in the standard Mastersbilt Smackdown and S7 spindles. Are there markings or a way to measure and find out what I have?
  14. 1-2 years old. Marshall, TX. My dad raced there...

    1-2 years old. Marshall, TX. My dad raced there around 1964-1966
  15. Thread: RR shock angle

    by ace1
    Replies
    4
    Views
    3,862

    It looks to be added but might not be. The welds...

    It looks to be added but might not be. The welds don't look the same but they did a very good job. So moving inward will soften spring and add drive? I'm on non adjustable shocks. If I have the car...
  16. Thread: RR shock angle

    by ace1
    Replies
    4
    Views
    3,862

    RR shock angle

    I have a 08 Mastersbilt that has had a shock mount added to the chassis on the RR which will lean the shock more in toward center of car. What's the thoughts on moving it in? What would be more...
  17. Thread: DIY Tire machine

    by ace1
    Replies
    6
    Views
    2,852

    I saw one made from a small winch. They just used...

    I saw one made from a small winch. They just used the motor and rigged up a coupler. Mounted a battery on the stand and just used 12v.
  18. Replies
    0
    Views
    1,976

    Mastersbilt rear deck height

    08 mastersbilt. What is the height of the rear deck support. I know rules may have a lot to do with it. But if making a new rear deck support how long would you make the tube to the bumper. I’m not...
  19. Replies
    3
    Views
    2,645

    View Post

    36 1/2

    I don’t know why I have to put 10 characters in the post.
  20. Replies
    3
    Views
    2,645

    Aluminum drive shaft?

    I don’t see many if any aluminum drive shafts in my area. What are thoughts on these. I’m needing one and found a used one from a reputable source. I’ve only used steel in the past.
  21. Replies
    8
    Views
    3,425

    I have one of the wissota cars I'm getting...

    I have one of the wissota cars I'm getting together. Its a 08 I'm told, round tube 01370W. The engine is set back more. My son has a 08 square tube and I have to use a shorter drive shaft than his...
  22. Replies
    0
    Views
    1,533

    08 Mastersbilt Wissota setup? edited

    What are differences in the Wissota and Std. smackdown chassis? I have found the engine is set back different and the rear end doesn't set the same left to right. I have 17" instead of 15 3/4 from...
  23. Replies
    5
    Views
    2,876

    Is there any other differences on the wissota...

    Is there any other differences on the wissota cars. I was just checking the rear end side to side and it doesn't measure to the book spec.
  24. Replies
    5
    Views
    2,876

    That is it. It does have a W. I wondered about...

    That is it. It does have a W. I wondered about that. Thanks
  25. Replies
    5
    Views
    2,876

    17.5/15.5 both sides

    17.5/15.5 both sides
Results 1 to 25 of 172
Page 1 of 7 1 2 3 4

All times are GMT -5. The time now is 06:15 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.