Search:

i have a 2008 cyclone/rocket chassis 4 bar z link was wondering what leight of nine inch floater to put in it and where i can get a lift bar kit for it for a floater than isnt a quick change it had a...

do I mount it up right or upside down ive seen guys with them upside down ?

i have a Camaro chip Intimidator Chassis car I am on a multi leaf on the left rear and a mono leaf on right rear with a coil over emlimator it is not floated like a fast boy . i am running 75 in...

no i have aluminum one I will try that I orderd a new hold down from allstar that goes around the neck and tightens when a allen head holds it from moving so hopefully that works also.

im have a mallory distributor looks like the msd distrubitor with the slip car when im on the track under power my distributor moves so my timming moves and the car dies , has anybody else ever had...

i have a c&S alchol carb that uses gas jets has the two little holes in the metter blocks I have 90 jets in front and back everybody I run with runs .160 jets I was wondering if someone could tell me...

wondering if someone could help me I got a c&s billet arocal carb running on alchol running a 10AL fuel line to my 15psi pro cam fuel pump then 8al to the log with a 8 an return line. I wanting to...

wondering if I can run synethic oil in my methonal race engine? all the guys I run with have always used just VR1 but im wanting to run a synethic

i got a 428ci small block chevy dart little m block, dart pro 1 heads 215cc 14:5:1 compression 4.000 stroke 4.125 bored and 6 inch rod , 645 lift roller cam straight acrossed. I don't know what size...

i was wonder if anybody runs the demon alcohol carbs i got a 750 i can buy are they any good ? ive hurd a few guys around me say they have had problems with them.

i have a intermantor chassis super stock camaro clip with the mono leaf with a slider on right side and a multi leaf on the left side we won with it this last year a few times it gets hellaush...

what do i do with the other port on the bypass regulator i know theirs an in and a out the bottom port is the fuel cell return line do i plug the out port off ?

ive seen some mods running block mecanical 15psi pumps on methonal with a 5/8s feed line it looked like it had a regulator on the back on the fuel log on the return. id like to run a setup like this...

alright i stuck a 6.200 rod on it and put it on the crank in the block its really close to 0 deck im gonna take it to the machine shop and have them make up the diffrance. thank you for the help

so if i use a 6.200 rod it makes it about 2 thousands off and i can make that up in decking right ? how would i know the compression of the piston is it still the same as what the sheet says on it ?

i was wondering if anybody knew if i can use a 395ci piston 6in rod on a 3.480 crank i got them setting next to my 350 6 in rod pistons and it doesnt look like their is much of a diffrance? the pins...

i have a 355 dart heads 14:5.1 compression been winning with it my exhast valves hit my pistons their 1.6 but my 2.08 intakes did not and my cam is straight acrost .640 and my valve lash is .020...

does anybody know a good afordable agressive brake pad for a camaro chassis? i turn my with the brake i have a 3 brake setup, im wanting to put an agressive left front on so i dont to put everything...

i was wondering if anybody could tell me if the RHS 14 degree cast heads used a standard straight up shaft rocker or an offset chevy rocker ?

i got a 800 billet aerosal carb for metonal and it has screw in air bleeds their is no air bleeds in it and or jets i see it has the holes on it like in the willys carbs where u can run gas jetts ....

whats the differance between a coil over slider and a coil over elmantor are they the same thing just differnt names for them ?

its a 14:5.1 355ci .645 lift roller cam light crank and rods. doesnt make its peak power too about 7500rpms its really strong down the straight away justs pulls away

their brand new ,yes their soild ive already had it too 7600 rpms on the track so that takes that out my roller is in the center of my valve stem and my rockers are clearing the springs and i set the...

the cam company wanted like #590 with it open with the high rpm use of it. its a late model camshaft. i didnt set the heads i had a guy thats done race heads for years do it to the specs they wanted....

no i dont run them im getting plunty of oil up their this is my first roller cam i always ran them with soild flat tappet cams . i orderd a set of good sever duty roller rockers they think its...