Search:

Helping a buddy that just bought a front steer nova motor stock location maybe 1" back, he will run 3 speed Saginaw. Car has a 12 bolt in it that is suppose to have the correct gear in it for the...

I have used a torch I thought it was alum and we couldnt figure out why it looked like sparkler things fly off? Now I pay lil more attention before I think about using a torch.
I figured it would...

Got to replace R&P in a mag center and maybe a tube so thought about throwing the rose bud to it like I have aluminum bells and centers ---------- then said NO. So I picked up an old oven that was...

I have a mic I installed and looking for speakers. Any one got input on reasonable price and quality? Was gonna get local guy to install speakers but thought I would ask first. thanks for input.

This was kinda my main concern that it just wont be high enough. We have been using the steel jack from the shop but that thing gets HEAVY lifting in and out of truck bed! gonna wait and see how...

We where thinking about getting a aluminum jack for next year. I have seen alot of guys using the Harbour Freight jack you can get for like $60 it raises to 14-3/4" and has one wheel all the way...

Dumb question I guess but are carrera abd QA1 shocks the same now? I am just wondering cause I picked up a set that had been built by ARS and a buddy told me they were the same shocks as QA1? Hate to...

Fuel cell is mounted to 2x3" fuel cell brackets. frame is 2" round tube. Sorry for confusion on that. Also front bumper that is on it slides into front frame horns and is held in with 1/4" bolt on...

the steering shaft is not in the car and there is no rear mount under the dash? There looks as if they may have been a clamp on mount but not for sure. The owner says car is just like he bought it he...

Loooked down through access panel for a number on the bars and didnt see one. I looked on warrior site and only showed 03 and 04 as underail cars so I guess its a 03 or 04.

Looking at a warrior and was wanting to know if they have numbers or a way to identify year? Has 5 holes for upper 4 bars and 3 for lower bars, under rail car, square upright that j bar adjust moves...

I would just take a 7.00 gear set for a 4.86 r&p of transfer gear and drop in. Mark and turn the yoke and if it makes about 7 round to 1 of the hubs, it's probably a 4.86 if not it's something else.

Thanks found it, a little higher than I thought.

I saw a guy selling a reapir sleeve thing for bert tail shaft seal or housings a while back any body remeber this and know how to in touch with them?

Got a aluminum weld weld non beadlock that made contact with another car and folded the lip around maybe 2". The lip is close to the flat part of the bead now. The wheel runs true other than the lip...

Run into a guy that has a box full of new and slightly used 1 X 3" lower arm for my car. He said thats what he ran when he raced and just had these for spares. He wants to trade for some old car...

I may be wrong but I think the snout is copied from 3/4 ton chevy rear and takes those bearing and seal. The old double nuts with a washer that folded over to lock the 2 nuts together was taken from...

Would running snap hook ratchet tie downs over tires 2, 3, 4 tires? or tieing to rear axle and some where under front be better? We had winch cable and ties over LF and RR but are questioning it...

What is normal, not so good, and bad on oil temp for a 604 and what can I do other than an oil cooler to lower oil temps?

P.M. sent to you repond when you get time.

The car I bought didnt have all the gauges in it and I was going to just make new panel and put my old gauges in it. The late model has a place for a Oil temp and a fuel pressure gauge. I have never...

Has anyone used these scales and know if they would be a good start for a new guy? thanks for any input.

http://www.speedwaymotors.com/Longacre-Racing-AccuSet-Electronic-Scale-Set,25598.html

I have a stinger - GRT copy. The grt setup sheets and the sheets I got with the car say 10" on RF,LF, and 5th coil 14" on LR 12"RR.
I was thinking a 12" on the RF would be better idea to limit...

Ironic you just responded cause last night I was laying in bed thinking about spring compression "boy am I getting old". But say a right right side spring as the car rolls on the spring and it...

Does the length of the coil spring make a noticable difference, if it does not bind? If so does a certain corner or the 5th arm make a bigger difference?

Example- In your setup sheet from builder...