Search:

Type: Posts; User: Confused?

Page 1 of 15 1 2 3 4

Search: Search took 1.12 seconds.

  1. Thread: 90/10 shock

    by Confused?
    Replies
    1
    Views
    666

    View Post

    The “old school” mounting introduces too much angle in the 90/10 at a dynamic state. A lot of mods are running flatter pullbars now than they used to. It’s all about how the car act during the race,...
  2. Replies
    13
    Views
    1,282

    View Post

    Maybe he’s sending them out to get ground up. A lot of arenas use old ground tire chunks for footing. They can’t be steel belted so the bias ply racing tires work perfectly
  3. Thread: Nova lowers

    by Confused?
    Replies
    3
    Views
    727

    The drag link, idler arm, and pitman arm have to...

    The drag link, idler arm, and pitman arm have to match the frame too
  4. Replies
    16
    Views
    949

    View Post

    If I understand the OP correctly, he’s running an IMCA northern sport mod. That means solid pullbar within 1” of centerline of driveshaft, solid pullbar, no springs or bushings springs on top of axle...
  5. Replies
    1
    Views
    416

    No, they can not

    No, they can not
  6. Replies
    4
    Views
    490

    You can get a ton of dynamic roll steer with a...

    You can get a ton of dynamic roll steer with a three link. Sport mods have been doing it for years. It's all in the dynamic angle and droop.
  7. Thread: J-Bar Theory

    by Confused?
    Replies
    45
    Views
    5,822

    These points have my curious about one other...

    These points have my curious about one other change. When would someone move the j-bar right or left without changing angles or lengths?
  8. Thread: Front stubs

    by Confused?
    Replies
    1
    Views
    788

    Camero clips are not legal. Mods must be based on...

    Camero clips are not legal. Mods must be based on a full frame car
  9. Replies
    11
    Views
    550

    Maybe it's changing caster or camber...

    Maybe it's changing caster or camber dramatically, or bad heims in the lower
  10. Replies
    7
    Views
    1,402

    They are Hawk 30

    They are Hawk 30
  11. Replies
    12
    Views
    639

    Intake leak or broke header/gasket

    Intake leak or broke header/gasket
  12. Replies
    6
    Views
    1,110

    Drive it and then decide what it needs

    Drive it and then decide what it needs
  13. Replies
    4
    Views
    949

    If the mounting bracket on the rearend is a clamp...

    If the mounting bracket on the rearend is a clamp bracket, put it on top. If it's in front or rear, it could spin on the housing causing more drop than needed or wanted. If the bracket is welded to...
  14. Thread: Strange Oval

    by Confused?
    Replies
    4
    Views
    1,127

    Some mod drivers still use them

    Some mod drivers still use them
  15. Thread: lr hike

    by Confused?
    Replies
    15
    Views
    2,599

    That depends on the amount of drop and the lower...

    That depends on the amount of drop and the lower bar angle. The more split between the bars cause more indexing. My last four bar car would bind the birdcage when the top bar hit 51 degrees. It would...
  16. Thread: lr hike

    by Confused?
    Replies
    15
    Views
    2,599

    Did any of these suggestions help your concerns?

    Did any of these suggestions help your concerns?
  17. Replies
    3
    Views
    621

    I can't open them either.

    I can't open them either.
  18. Replies
    10
    Views
    875

    I've always had good luck with the white Lennox...

    I've always had good luck with the white Lennox hole saws.
  19. Replies
    19
    Views
    1,583

    Time for a rebuild

    Time for a rebuild
  20. Thread: lr hike

    by Confused?
    Replies
    15
    Views
    2,599

    I would drop both left side bars. The top down...

    I would drop both left side bars. The top down 20-24 degrees and the lower to 4-8 degrees at ride height. I bet the excessive bar angle is causing the birdcage to bind and not drop any further.
  21. Thread: lr hike

    by Confused?
    Replies
    15
    Views
    2,599

    Are those bar angles at full drop or ride height?...

    Are those bar angles at full drop or ride height? Too much for ride height and not enough for full drop.
  22. Replies
    25
    Views
    3,652

    You've made a couple of statements in you post...

    You've made a couple of statements in you post that make me think your cars is WAY too tight. Contact your chassis builder and get a base setup. You can tune from there. You have given no info other...
  23. Replies
    7
    Views
    1,148

    It's like having a posi-track versus a spool

    It's like having a posi-track versus a spool
  24. Thread: Turned stub

    by Confused?
    Replies
    5
    Views
    2,022

    IMCA dictates the minimum and the maximum. The...

    IMCA dictates the minimum and the maximum. The sides do not have to match.
  25. Replies
    5
    Views
    2,704

    IMCA rules only allow OEM lowers and suspension...

    IMCA rules only allow OEM lowers and suspension components except you can use the IMCA approved uppers. They also have to be on the correct sides of the car. You won't be able to get the RF out like...
Results 1 to 25 of 354
Page 1 of 15 1 2 3 4

All times are GMT -5. The time now is 12:02 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2020 vBulletin Solutions, Inc. All rights reserved.