Search:

Type: Posts; User: Wild Blue 32

Page 1 of 3 1 2 3

Search: Search took 1.17 seconds.

  1. Thread: e85

    by Wild Blue 32
    Replies
    3
    Views
    845

    I run E85 in my wissota mod 4. I buy my fuel at...

    I run E85 in my wissota mod 4. I buy my fuel at the pump mid summer when it's closest to 85% ethanol. if you buy it when it's colder out it might be more like 70%. I always check the ethanol...
  2. Replies
    0
    Views
    1,017

    Dyno Tuning

    I'm taking my 2.3 ford to the dyno. What do I tune to gain power? I'm assuming carb jets, timing, and valve timing. Any other suggestions. Thank you. Wissota mod 4 rules.
  3. Replies
    38
    Views
    6,359

    I've been running pump E-85 for 2 years now. What...

    I've been running pump E-85 for 2 years now. What I do is buy the fuel in june or july when the pumps would be closest to E-85. Then I test it and add unleaded gas if it's too high ethanol content or...
  4. Replies
    10
    Views
    3,562

    It is a solid cam. it seams to run really good....

    It is a solid cam. it seams to run really good. what do you mean is the cam asymetrical? It is 515 lift intake and 520 lift exhaust.
  5. Replies
    10
    Views
    3,562

    I talked to the guy that set up my head. He said...

    I talked to the guy that set up my head. He said he set it up with 115 pounds seat pressure. How will I know if Its not enough? Will I here the valves float or will it just not run high RPM? Thanks...
  6. Replies
    10
    Views
    3,562

    JD Are you saying the valves will float at 95...

    JD Are you saying the valves will float at 95 pounds?
  7. Thread: Muffler

    by Wild Blue 32
    Replies
    4
    Views
    1,982

    I have the software. It doesn't tell where to put...

    I have the software. It doesn't tell where to put the muffler though. Should the muffler be right off the header or at the end or? Thanks for the responses.
  8. Replies
    2
    Views
    1,053

    How about prothane bushings? Has anyone used...

    How about prothane bushings? Has anyone used them? They are a quite a bit cheaper.
  9. Replies
    2
    Views
    1,053

    Mustang 2 Control Arm Bushings

    Does anyone know where I can get bushings for the mustang 2 upper and lower control arms? I have the speedway control arms now but I'm looking for better bushings that I can replace myself.
  10. Replies
    2
    Views
    1,358

    You need to burn 30 percent more fuel. It isn't...

    You need to burn 30 percent more fuel. It isn't as easy as just increasing jet size the passages in the carb need to be opened up as well. I burned E85 last year with a holley 500 and the 2 seasons...
  11. Thread: Muffler

    by Wild Blue 32
    Replies
    4
    Views
    1,982

    Muffler

    We have to run mufflers. Wissota mod 4. Does anyone know anything about schoenfelds anti-reversion chamber? Would it qualify as a muffler? Would it help with power? 2.3 Ford with power by ace...
  12. Replies
    10
    Views
    3,562

    The guy I bought my cam from told me 90 or 95...

    The guy I bought my cam from told me 90 or 95 pounds on seat. Any more and it costs power. I guess i'll try that. Thanks for the responses.
  13. Replies
    10
    Views
    3,562

    Valve Spring Pressure

    What kind of valve spring pressure should I run on the seat and max lift. It's a 2.3 ford solid lift head with .525 lift. I've heard numbers all over the board from 90 on the seat to 150 on the seat....
  14. Replies
    9
    Views
    2,095

    I burn E85. Would I still want to block the water...

    I burn E85. Would I still want to block the water passage?
  15. Replies
    6
    Views
    1,984

    Just curious. How much better would a 2.5 be than...

    Just curious. How much better would a 2.5 be than a 2.3?
  16. Replies
    9
    Views
    2,095

    Intake Gasket

    BY rules we are required to run the oval port head along with the oval port intake. I read somewhere that the oval port intake ports are too big for a 2.3. And by filling the bottom of the intake...
  17. Thanks to everyone that replied. we're gonna try...

    Thanks to everyone that replied. we're gonna try it.
  18. Sorry. 2.3 ford.

    Sorry. 2.3 ford.
  19. 1 piece rear seal crank in a 2 piece rear seal block?

    Can I use a a crank from a 1 piece rear seal block in the older block that requires a 2 piece rear seal? Or do I have to use a crank with the oil slinger. The reason I ask is I ordered a new crank...
  20. Replies
    11
    Views
    2,211

    The shaft in the transmission should be straight...

    The shaft in the transmission should be straight and there should be a plastic grommet on it. You,ll need to change the shifter shaft in the transmission.
  21. Replies
    1
    Views
    1,460

    Anti squat and rear steer on a 3 link

    My question is when setting bar angles on a three link do the trailing arms create anti squat or is it the pull bar? Say you have 20 degree angle on your pull bar and you want dynamic rear steer. By...
  22. Anti squat and rear steer on a 3 link

    My question is when setting bar angles on a three link do the trailing arms create anti squat or is it the pull bar? Say you have 20 degree angle on your pull bar and you want dynamic rear steer. By...
  23. Replies
    5
    Views
    1,520

    Also, how high should it be off the rear end...

    Also, how high should it be off the rear end housing?
  24. Replies
    5
    Views
    1,520

    Thanks. Right now it is 4 inches left of center...

    Thanks. Right now it is 4 inches left of center on the rear end with the chassis mount a little farther left. How big of an adjustment would it be to center it?
  25. Replies
    5
    Views
    1,520

    Any suggestions?

    Any suggestions?
Results 1 to 25 of 67
Page 1 of 3 1 2 3

All times are GMT -5. The time now is 07:58 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.