|
|
Search:
Type: Posts; User: 96racing
Search:
Search took 0.20 seconds.
-
Not sure what car you have but in a Rocket most run 1" spacers under the front motor mounts and the midplate has two sets of holes to allow it to also be raised 1".
-
If they are 15", make sure you're getting D load and not C. I had several blowouts and after lot of research, I bought Maxxis tires and haven't had an issue since. They ar the only 15" trailer tire...
-
If you have either the yellow Jones all billet fan or the yellow fan with the riveted blades, definitely get rid of it. They had trouble with both. The new Jones 3 blade is made by Race Fan. The 19"...
-
I have pretty much the same parts you've mentioned. I have a 16AN dual pass radiator and a shroud that has about half of the fan in it. I run the Race Fan but use the three blade 19". I know guys...
-
We used to burn about 5 gallons of race gas for a 20 lapper
-
Check your PM. I just sent you something
-
Longacre sells this setup in a kit for like $25
-
-
Jimmy Jesmer of Pasadena MD. has a nice 15 blue front rocket with fresh 2020 updates, new body and XR1 left rear four link plates. Been for sale for a while and he just dropped the price again. If...
-
I believe that is the way the Brinn Predator is also. When in high gear, it only turns the input and output shaft and not the entire gear cluster like the original Brinn trans does hence free...
-
I spoke with the ProFab guy at a motorsports show last year. He said they had dyno'd a set at Hendren on Dillion Brown's 604 car and there was a gain of 5 HP. Didn't say where that HP was in the RPM...
-
All of the B/G stuff will work. The '15 update should give it the flat plate rack mount which has additional ground clearance. There is one more update in '18 that gives an additional 1/2" of...
-
Brad,
We run a RUSH 604 dirt late model. Mostly interested in comparison between the 1" HVH that everyone runs and the newer 5/8" to see which would be the most beneficial.
-
Most of the Stealths are 700 cfm and the Bakers are 750. That is what most guys around here are running. We had good success with one of the old 750 Stealth carbs that had the extra 1/2" spacer...
-
Brad, I have a new question that I'm interested to learn about pertaining to the 604. Which carb spacer makes the most power on the dyno and which one do you recommend? And where would that power...
-
Call Rocket and give them the serial number. They will send you a setup manual with all of this info in it. I had a buddy just convert his 15 Rocket over to a modified. He took it to Brucebuilt in...
-
-
We don't have an XR-1 but I've heard of a couple local Super teams that went back to 16 cars because they didn't like the 18.
-
-
we use this and it works well...
-
When you buy a set from Brad at Race 1, he has checked them and has them marked them for intake and exhaust. He charges $150 for a set. They are normally $75/set but it takes two sets to get a full...
-
With 1.25" rotors, I have 7" from inside of RR rotor to shock mount centerline and about 7-3/4" on left side from inside of rotor to shock mount centerline. My rear was originally in an 05 Black...
-
-
I've had issues with the heavy racing plug wires before. I always swap out #1 plug wire with an old stock one I have laying around.
-
On a 1/2 mile track with a 6 lap heat and a 15 lap feature, we burned right around 5 gallons. I doubt you will be able to get anywhere near 2200# with a steel head steel block 602 and still get your...
All times are GMT -5. The time now is 02:07 AM.
|
|