Search:

Type: Posts; User: racer21

Page 1 of 6 1 2 3 4

Search: Search took 2.98 seconds.

  1. Replies
    1
    Views
    1,967

    Metric floater choice?? CENTERED OR OFFSET??

    Helping a friend put a car together he has to buy a rear and we are trying to decide if he should go with a 60 centered or the 2in offset. Pro's and con's of each would be greatly helpful Thank You...
  2. Replies
    8
    Views
    2,226

    Checking floater rearend for straightness

    Ok guys the way I done it was install two straight wheels set it up on blocks and spin the rearend,not sure if this is correct but the wheels move in and out,now for the good part I got the second...
  3. Replies
    22
    Views
    8,778

    Metric rear trailing arm mts??

    Wondering what kinda angle people try to acheve on the rear uppers,i have to put new mts on top and was wondering if I should put more angle in the bars or less? Anyone know?
    Pros and cons of each...
  4. Replies
    0
    Views
    919

    Metric floater rearend offset??

    Looking at putting a floater in and was wondering if a centered or the offset would be best,i was thinking 60in on width. whats everyone opinon,THANKS
  5. Thread: Loose off gas

    by racer21
    Replies
    20
    Views
    5,721

    ballast to far back??

    ballast to far back??
  6. Replies
    1
    Views
    1,502

    Metris rear spring question??

    I see some builders add a 3 inch tall bucket to the rear top spring pads and run the 16 inch springs and some builders don't add it and run the 13 inch springs, Is there a specific reason for doing...
  7. Replies
    2
    Views
    1,155

    Sbc oil pump??? And oil pressure readings??

    Looking at recommendations for sbc oil pump,going in a stock block motor in the past ive run the melling 10550?
    Whats everyones opinon?
  8. Replies
    1
    Views
    1,464

    2 barrel carb engine intake choise

    Looking for the best option for a intake on a 2 barrel motor rule? Here is a few specs: 400 cubic inch,dart heads 200 runner roller motor,i have a few to choose from witch are the super victor,victor...
  9. Replies
    17
    Views
    3,256

    Thanks guys for all the input,problem has been...

    Thanks guys for all the input,problem has been found after several years of building my own stuff it was a first,i always check clearances and use plastigauge also ring gaps are always checked and...
  10. Replies
    17
    Views
    3,256

    Thanks guys for all the comments I have checked...

    Thanks guys for all the comments I have checked and rechecked every single thing suggested motor is coming back out and looks like im going in DEEP i'll post what I find in a few days,thanks again
  11. Replies
    17
    Views
    3,256

    Thanks Guys, smoke is bluish color and a raw oil...

    Thanks Guys, smoke is bluish color and a raw oil smell,heads are new and seals do look good after double checking,intake matches good and seals(I even changed gaskets yesterday to be safe),heads are...
  12. Replies
    17
    Views
    3,256

    new motor question HELP PLEASE

    I 've spent all winter building a engine got it all done primed ready to go,after getting it in the car and letting it build up temp to seat rings it starts smoking,so I shut it off and try again the...
  13. Thanks let-r-eat would you know what pressure's...

    Thanks let-r-eat would you know what pressure's to start with?
  14. Afco bulb series shock, base valve, with scrader valve tech please

    Got a nearly new set of the base valve shocks in on a trade deal and trying to find out what kinda gas pressures to set them at and what adj to make and when,cant seem to find any info on the...
  15. Anyone run the AFR SBC Titon Intake Manifolds ?? Reveiws good or bad???

    Has anyone run this manifold on dirt? Any feed back compared to the victor series intakes??
  16. Replies
    8
    Views
    2,674

    Newbie have you done anything on heads? Im...

    Newbie have you done anything on heads? Im thinking no one is running the mullins head or its all top secret,i haven't found anyone that has run them. :-/
  17. Replies
    8
    Views
    2,674

    I was wondering if anyone was running the head...

    I was wondering if anyone was running the head also and had any comments as well.
  18. Motor Guys Here's a Question Concerning Crank To Rod WT To Piston Wt

    Only reason I ask is because I just don't know, heres what I got I picked up a callies mangun crank from a friend that changed directions in his build witch if I seen right is a little lighter than...
  19. Replies
    4
    Views
    1,689

    Thanks guys for the replys and positive comments...

    Thanks guys for the replys and positive comments I will be giving them a try soon, :-}
  20. Replies
    4
    Views
    1,689

    Howards Racing Componets Question

    Has anyone had any experience (good or bad) With the howards promax crank and rods,possibly going in a 400 base motor on 2 barrel dirt car,thanks in advance
  21. Replies
    2
    Views
    1,185

    Who all out there cnc's steel heads?

    Looking for a place to have some steel heads cnc'd, whats the pro's and con's of this process?
  22. Dart platium 215 or world products 200 what'S better

    I recently bought a 406 2 barrel motor that come with the sportsman heads on it but also come with a extra set of the dart platinum 215 would it be worth the gaskets to change,running in a 3200...
  23. Replies
    2
    Views
    1,611

    Rhs steel head 12336 plug num ??

    Im trying to figure out what plug I need for these heads I know its a tapered .704 reach and I need one with the shorty tip, anyone have any numbers for these,there on a 2 barrel motor on gas,Thanks...
  24. Replies
    4
    Views
    2,989

    Tighten Metric Car??

    IM wondering when people say they are tighting there race car what are they doing.Had a guy tell me he made his car to tight by adding stagger,Is this right or wrong? My thought to tighten for slick...
  25. Thread: ride heights

    by racer21
    Replies
    11
    Views
    5,037

    Thanks a ton!!

    Thanks a ton!!
Results 1 to 25 of 136
Page 1 of 6 1 2 3 4

All times are GMT -5. The time now is 03:35 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.