Search:

Type: Posts; User: BigBlueFord

Page 1 of 4 1 2 3 4

Search: Search took 0.24 seconds.

  1. Replies
    7
    Views
    1,648

    I pretty much agree with DirtRacer9x, except I...

    I pretty much agree with DirtRacer9x, except I would suggest preloading the spring about an inch before starting to measure in 1 inch increments. Also be very careful. That loaded spring can do...
  2. Replies
    15
    Views
    2,999

    How about running a half inch longer stud in the...

    How about running a half inch longer stud in the balljoint. You should check and see what impact this will have on your roll center, etc.
  3. Yuppers, RR is ahead of LR.

    Yuppers, RR is ahead of LR.
  4. Rearend Right Rear Lead.....How much is too much?

    Can you reach a point where too much right rear lead will actually lose forward bite instead of tightening the car? Is 1" too much?
  5. I've never had a Taylor wire fail.

    I've never had a Taylor wire fail.
  6. Replies
    4
    Views
    1,195

    http://quickcar.net/index.php?crn=255&rn=1060&acti...

    http://quickcar.net/index.php?crn=255&rn=1060&action=show_detail Water Temperature Switch 3/8"NPT 61-748
  7. The 2014 IMCA Mod rules are posted. Crates now...

    The 2014 IMCA Mod rules are posted. Crates now get a 2" spoiler, not 3".
  8. Replies
    5
    Views
    1,038

    I don't think so. It sounds to me like you have...

    I don't think so. It sounds to me like you have the wrong tach for your application. It sounds like you have a tach for a magneto not a distributor.
  9. I heard the IMCA is gonna make an announcement of...

    I heard the IMCA is gonna make an announcement of the 2014 IMCA Modified rules changes at the PRI show.
  10. Replies
    9
    Views
    6,587

    Weight Differnce SBC vs 604 Crate

    What is the weight difference between a small block Chevy and a 604 crate engine?
  11. Replies
    5
    Views
    1,371

    Here's info right out of the Winter's catalog:

    Here's info right out of the Winter's catalog:
  12. Replies
    10
    Views
    1,646

    It's hard to find a better balljoint than Howe. ...

    It's hard to find a better balljoint than Howe. Plus they're rebuild-able and you can get different length studs to help getting your front roll-center set correctly without having to ream spindles.
  13. Replies
    4
    Views
    2,033

    The BSB slider is real easy to rebuild. I'd...

    The BSB slider is real easy to rebuild. I'd suggest taking it apart to determine what parts you need then give BSB a call and order them. While you have them on the phone you can ask for any tech...
  14. Replies
    12
    Views
    2,854

    Very good seat. I'd strongly suggest ordering...

    Very good seat. I'd strongly suggest ordering the seat with right and left leg supports. The leg supports greatly increase the driver protection by more securely holding him in place. If you wear...
  15. Replies
    2
    Views
    776

    Clearance between the face of the flywheel and...

    Clearance between the face of the flywheel and the face of the starter idler gear should be 0.060" to 0.080".
  16. Replies
    5
    Views
    1,559

    Perfconn......Do you have any suggestions for...

    Perfconn......Do you have any suggestions for ways of keeping/getting oil back down into the pan on a wet sump, 23*, flat tappet, (IMCA legal) engine? We're already running drain down lines off...
  17. Replies
    4
    Views
    1,406

    Contact Joe Garrison at GRT. MAILING ADDRESS:...

    Contact Joe Garrison at GRT. MAILING ADDRESS: GRT Race Cars, Inc. 83 South Broadview Greenbrier, AR 72058 CONTACT NUMBERS: Phone: 501-679-2311 Fax: 800-880-0478 EMAIL ADDRESS:...
  18. Replies
    3
    Views
    883

    From Winters catalog:

    From Winters catalog:
  19. Replies
    3
    Views
    1,179

    Directly from the Winter's catalog: Important:...

    Directly from the Winter's catalog: Important: Shut Off Power 1. Elevate car 2. Remove quick change gears 3. Chalk mark the tire at 12 o’clock position 4. Chalk mark the pinion at 12 o’clock...
  20. Replies
    6
    Views
    1,340

    Brinns also also use a pilot point set screw to...

    Brinns also also use a pilot point set screw to help retain the bushing in place.
  21. Replies
    6
    Views
    1,340

    I always use LOCTITE #620 GREEN SLEEVE RETAINER...

    I always use LOCTITE #620 GREEN SLEEVE RETAINER on the bushing when I install them.
  22. Replies
    6
    Views
    1,587

    When the scales shutoff, do you have to go around...

    When the scales shutoff, do you have to go around and turn each one on individually or does just rolling the car off and on the scales turn them on?
  23. On our mod the upper and lower balljoints studs...

    On our mod the upper and lower balljoints studs are different diameters. Do I have to compensate for the diameter difference or just read directly. Do you use this method as your primary method for...
  24. Replies
    2
    Views
    887

    Quick n dirty way is to just use lumber. You can...

    Quick n dirty way is to just use lumber. You can build just a roll-off or build a a box to get some height to make it easier to work under the car to make adjustments. 1" square tubing and and some...
  25. Replies
    4
    Views
    1,401

    Alky will require a smaller jet in the return...

    Alky will require a smaller jet in the return line fuel pump port.
Results 1 to 25 of 80
Page 1 of 4 1 2 3 4

All times are GMT -5. The time now is 06:42 PM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.