Search:

What are the brake pads that spark.Metric calpipers.
I dont care if i have to replace the rotors every week.

I am installing an alternator this year and have a concern that my master kill switch that is mounted in the negitive battry calbe will not kill the motor?
I know on a street car if you remove the...

I am installing an alternator this year and have a concern that my master kill switch that is mounted in the negitive battry calbe will not kill the motor?
I know on a street car if you remove the...

I am installing an alternator this year and have a concern that my master kill switch that is mounted in the negitive battry calbe will not kill the motor?
I know on a street car if you remove the...

I am installing an alternator this year and have a concern that my master kill switch that is mounted in the negitive battry calbe will not kill the motor?
I know on a street car if you remove the...

Can anybody figure out what brake pads these are?They are from metric rotors.Came off the front and i had wilwood D154 in the rear....Wondering if these are similiar or ???

Can anybody figure out what brake pads these are?They are from metric rotors.Came off the front and i had wilwood D154 in the rear....Wondering if these are similiar or ???

Thank you rrrrick
part is ordered !!!!!!!!!!!!!!!!!

Looking at putting a alternator on my chevy motor but the heads are not tapped out ?
Are there any moutning kits that fix this problem?

Looking at putting a alternator on my chevy motor but the heads are not tapped out ?
Are there any moutning kits that fix this problem?

Car was purchased in the winter of 2013.
We ran the car in 2013 and at the end of the year it was stripped down, powder coated and reassembled with LOTS of new parts,
Here are a few parts that...

Anybody have a part number
or place to buy a tailshaft housing seal for a fulcan trans?

new AFCO 5inch Progressive pull bar spring Part #270000PR

Selling a brand new AFCO 5inch Progressive pull bar spring Part #270000PR
I bought this , and then switched to a biscuit pull bar.
This spring lists for $89 at speedway....
A Serious racer would...

Thats what i thought.
Do you know what U joint is needed for quick change yoke?

Anybody have the measurement for driveshaft going from 9" to quickchange.
I am thinking we will all have the same length because there is no more options for different yokes, The only difference...

To The Top

Selling 6 Integra Base vavle shocks
3- 9inch and 3- 7inch
All have been gone through and revavled the spring of this year. Only ran about 6 times this summer. -
If interested i will tell you what...

29.5 inch driveshaft-nice -fits narrow ford 9 inch yoke. Selling because its to short for new quickchange. 100 OBO

Nobody runs a Harris car??
I cant get Happis to answer me either?

On my 2011 Harris.
As far as the rear trailing arm brackets?
There is 3 holes, from front to rear ,in each bracket for the upper and lower arms.Not the holes to move the arm up or down, But the...

What do you guys use to connect the shifter rod to the hiem on on a falcon trans.
I have always used a clevis on my Bert, but on this falcon there is not room between the trans and the hiem for a...

I was reading the set up sheet i got from Harris and they call for a 1inch wheel on the right front?
Just wondered if any of you guys run this?I have always had 2inch on the front of all my cars...

Integra shock package-6 ,4000 series Integra bulb shocks. It is a basic 4 shock package with the 2 left side shocks mono-tube, and the 2 right side are base valve,
The other 2 are the DRY SLICK...

Been having this argument for months, one guy says you need soft right front to get the car over on the right front.700 on left-600 right
I say the car is already tight going in. You need to have...