Search:

Type: Posts; User: 7uptruckracer

Page 1 of 20 1 2 3 4

Search: Search took 1.38 seconds.

  1. Just to be clearer looking for what moving the...

    Just to be clearer looking for what moving the lower trailing arms on the rear end do that cause and effect. We have the traditional straight below the rear end style brackets and we also run again...
  2. Basically looking at a cause and effect deal....

    Basically looking at a cause and effect deal. Moving it up on rear end does what on a three link and down does what. We have rear and forward center pull mount cars in our class and then the...
  3. 2 link bar location same as birdcage theory?

    Running a 2/3 link modified. A lot of new cars run this rear centerpull design. Makes good traction. Have seen some crazy bar mount brackets these days. How do moving a bar down or up or center on a...
  4. Replies
    10
    Views
    1,320

    How did you set that up?

    How did you set that up?
  5. Replies
    9
    Views
    1,184

    View Post

    8 and 12. Youíll coil bind the top at a 6Ē the 8Ē was super close on the one I did and I only run 645 lbs of static load
  6. Replies
    19
    Views
    2,042

    View Post

    So say I for example run an Allstar 6 blade 15Ē (15 is all that will fit in this car). I need to keep the same size. Not sure the Allstar is cutting it. Should I go with a Race Fan 6 blade 4 blade or...
  7. Replies
    16
    Views
    2,023

    Knock stagger out next time it slicks off

    Knock stagger out next time it slicks off
  8. Replies
    12
    Views
    1,062

    View Post

    Ah didnít think of that and yes itís the LR identical brackets with upper and lower link holes just side by side
  9. Replies
    12
    Views
    1,062

    Awesome!! Thanks

    Awesome!! Thanks
  10. Replies
    12
    Views
    1,062

    We are in that same area racing with connections...

    We are in that same area racing with connections to him. That has me wondering, could be an old car of his. I just wanna know which ones are ďstandardĒ so I can start there before I go outside the box
  11. Replies
    12
    Views
    1,062

    View Post

    Thanks itís currently in the inside just they have a lot of stuff wrong. Itís definitely a B/G just never seen the brackets done like this and wanted to make sure I use the right set. Iíll call...
  12. Replies
    12
    Views
    1,062

    Yes after more and more research they have the...

    Yes after more and more research they have the two dimples under rocket I guess itís rocket 2 brackets but regardless. They have two sets of 4 link brackets side by side I guess someone got is...
  13. Replies
    12
    Views
    1,062

    It it one of their style of mounts from 2001-2008...

    It it one of their style of mounts from 2001-2008 they called them Rocket 2 style mounts BUT regardless I was wrong they are both Rocket 1 mounts side by side 7 hole bottom on one without an...
  14. Replies
    12
    Views
    1,062

    2010 Rocket B\G LR 4 Link Mounts

    Got asked to go look at one at the track last night, in a very ill handling B\G. It has dual row (Side By Side) looks like a mix of Rocket 2 &1 the Outter half looks like Rocket 1 and the Inner...
  15. You can also run the GM2 spindles that will widen...

    You can also run the GM2 spindles that will widen it out some too. also will help get your arm angles your to something more appropriate.Tweak the idler arm some for bump fudge a few mounting holes...
  16. Measure the spacing between the coils and buy the...

    Measure the spacing between the coils and buy the corresponding height rubber in the firmness if your choosing. I believe but donít quote me most the barrel springs are 1Ē
  17. Replies
    1
    Views
    519

    Slip Yoke Engagement

    How much is acceptable minimum at ride height? Itís 8Ē yoke so 6Ē of barrell.
  18. Replies
    1
    Views
    785

    90/10 shock

    Not for a DLM for OWM. I remember old school 90/10 were mounted uphill to chassis now Iíve seen a few mounted virtually same angle as the pullbar which is right and why?
  19. Replies
    0
    Views
    386

    Spindle ID

    How can I identify it I have an .810, 1Ē or 1.25 spindle I know more are .810 now and just use spacers but these are older.
  20. Replies
    23
    Views
    3,129

    View Post

    Use builders baseline. They canít make a setup baseline for each car and set of rules etc. After that once your care is decent you can take advantage of all your rules and fudge ride heights etc once...
  21. Replies
    8
    Views
    1,005

    Billet...have you cut on one say in an area to...

    Billet...have you cut on one say in an area to change a pin inclination???? :)
  22. Replies
    8
    Views
    1,005

    So update. Reamed out my spares. Then found 18 GM...

    So update. Reamed out my spares. Then found 18 GM #2 Spindles locally. All should be 10 degree, heard I might find 7 degree in an Astro Van. But they are $45 apiece a real steal. So Iíll just trash...
  23. Replies
    8
    Views
    1,005

    Reamed Spindle Repair

    So....I did a thing...reaming a GM #2 spindle. Not the easiest to find anymore. Reamed to the wrong mark and sunk the pin way to deep....anyone ever welded one up, and red redrilled it? I have heard...
  24. Thread: RF Setup

    by 7uptruckracer
    Replies
    25
    Views
    4,163

    It will scuff valance in hammer down. The car...

    It will scuff valance in hammer down. The car will travel about 4.5 in the slick and 4.75 in the tacky, I grew up running dirt and lates before I went to asphalt to run mods but still run both, but...
  25. Thread: RF Setup

    by 7uptruckracer
    Replies
    25
    Views
    4,163

    What do you mean crashing the nose early?

    What do you mean crashing the nose early?
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4

All times are GMT -5. The time now is 06:47 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2020 vBulletin Solutions, Inc. All rights reserved.