|
|
Search:
Type: Posts; User: CC57
Search:
Search took 1.31 seconds.
-
Hatchet, I don't think it has anything to do with how the fuel is positioned within the carb.
Rather, how the carb, and the output from the carb, is in relation to the runners on the intake.
-
-
New radiator for Southern Sport Mod.
Any recommendations on one particular brand of radiator over another? Don't know if the components on the build on one brand is better than the other.
Any...
-
New radiator for Southern Sport Mod.
Any recommendations on one particular brand of radiator over another? Don't know if the components on the build on one brand is better than the other.
Any...
-
Yes there are gains to be made. And, if you already have the spacer,other than the dyno time, it's essentially free HP
-
Thinking of using one of these in my Southern Sport Mod.
Anyone have any experience with them? Good? Bad?
I appreciate it
-
Ok, so other than the one Mod I ran in the past (with had a Brinn), all I've ever ran was either a P-glide or T-350.
So I don't have a good working knowledge of what's required and what is a good...
-
Are the Moroso Ultra 40 really that much better than say a comparable configuration MSD or Accell plug wire?
Also (and this is going on a Southern Sport mod), 8.5MM or 8.0MM? And that appears to...
-
Thanks for your replies.
Anyone else?
-
Any personal experience(s) with Karl's or CNC?
Good? Bad? Stay the h--l away?
Will be for an IMCA legal Southern Sport Mod engine.
Thanks all.
-
-
Is the Richmond transmission legal in a IMCA Southern/Limited Mod?
Thanks for your responses
-
What do you soak them in to soften them up?
-
I'm leaning towards the 8252, but...
bushracing67, what combination and application were/are you using the 8207?
-
What would be the best coil for this application?
MSD distributor part# 8570 mated with a MSD-6A(6420)and running a 6,200 chip. 602 Crate motor on an asphalt circle track with an average lap of 16...
-
All my race vehicles have have been locked and have been set so I could spin the engine, and then connect the ignition circuit and fire the engine.
Worked great on high compression motors, or...
-
Well, in case anyone is interested or can learn from my experience...
Removed the shroud, sealed off the radiator cap and plumbed in an expansion tank.
Results: never got over 200!!!
...
-
Help.
Getting at wit’s end on how to cool down my 602 crate motor in my HMP racetruck .
Had to pull off the track last race when the water temp hit 240
Change I’ve incorporated:
;...
-
1st of all, I sincerely appreciate all of the replies.
I'm leaning towards the following:
1) Replacing my lower pulley (the one mounted on the balancer). It looks to be worn out, so the belts...
-
Requesting suggestions on how to cool down my asphalt racetruck . It has been running consistently hot: 220 to 230 to 240 degrees. Race before last, the temp went to … well I don’ know, it buried...
-
Hopefully a reply that will give you a bit of confidence and comfort that you're not about to have an issue with a thermostat...
In my Dirt Mod, I was running on Alky/Methanol, which is...
-
-
Uping the reward.
You put me in touch with a buyer and I'll give you $200!
-
Really need to get this car out of the shop. Need to make room for new Asphalt Race Truck I'm picking up the week of 12/19.
Heck, you start adding up the individual pieces included in the package...
-
New Race Truck coming so I need to make room in my shop (and my bank account :)), so please make a reasonable offer
All times are GMT -5. The time now is 04:31 PM.
|
|