many parts for sale

[SCREAMIN1CAR]

lightning chassis birdcages nice-$150 pair_SOLD
lightning chassis bisquit pullbar, bushings one nite old-$75-SOLD
left side nova factory lower a arm-$50 - SOLD

[SCREAMIN1CAR]

lots of nice parts still for sale

[SCREAMIN1CAR]

to the top

[boyll65]

still have heads

[kencar87]

set of sbc canfield 220 aluminum angle plug heads-1 race old since fresh,roller springs good to .670 lift.-$700
weiand team g intake with raised plenum,fits 23* heads-$75
procam fuel pump,3 races old-$75
set of 1.5 7/16'' aluminum roller rockers,nice! these came from a cornetts racing engine employee-$100
set of .180 offset .842 roller lifters,1/2 set is crower 1/2 is isky-$80
gaerte custom solid roller camshaft ground for a 408'' sbc,small base circle-$100

Can you give a little more detail on your gaerte cam shaft ,specks etc. I am interested in buying but need more info. Thanks Ken send to kencar1952@yahoo.com

[SCREAMIN1CAR]

still have heads

i do still have the heads

[SCREAMIN1CAR]

Can you give a little more detail on your gaerte cam shaft ,specks etc. I am interested in buying but need more info. Thanks Ken send to kencar1952@yahoo.com

the cam card is at the engine builders shop,best i can remember its .650/.660 with 1.5 rockers. will find out more in a few days when i make it back to the machine shop

[SCREAMIN1CAR]

may take trades on some of this stuff,what do you have?

[SCREAMIN1CAR]

Bttttttttttttttttttt

[dirt 14]

im interested in the headers,but dont have a phone number,pm or call me,later Brook

[SCREAMIN1CAR]

hey brooke, 859 925 9211 home,859 779 4064 cell. thanks!

[SCREAMIN1CAR]

btttttttttttttttttttttttttttt

[SCREAMIN1CAR]

to the top!!!

[SCREAMIN1CAR]

btttttttttttttttttttttttttttt

[SCREAMIN1CAR]

set of sbc canfield 220 aluminum angle plug heads-1 race old since fresh,roller springs good to .670 lift.-$700-sold
weiand team g intake with raised plenum,fits 23* heads $75 sold
set of 1.5 7/16'' aluminum roller rockers,nice! these came from a cornetts racing engine employee-$100-sold
set of .180 offset .842 roller lifters,1/2 set is crower 1/2 is isky-$80-sold
gaerte custom solid roller camshaft ground for a 408'' sbc,small base circle-$100-sold

[Tn.Mod 2]

Have they been repaired , how many times resurfaced?

[Tn.Mod 2]

Sorry , just seen were sold!!

[SCREAMIN1CAR]

890 cfm c&s 2 barrel racing carb like new-$350-sold






















accell yellow super coil-$25-sold

[SCREAMIN1CAR]

bushore direct drive powerglide-$100
stock powerglide-$100
3 ring saginaw 3 spd-$100
795 edelbrock carb 2 races old on street stock-$100
brzezinski vortec cast intake 4 bbl-$100
3.23 richmond gear 8.5 gm-$50
canton rs dipstick oilpan dual kickout-$50
set of 1.52 comp cams roller tip rockers-$30
powerglide shifter-$40
case of joe gibbs oil-$50
set of crower offset roller lifters,1 pr damaged-$40

[SCREAMIN1CAR]

383 rotating assembly
eagle cast steel internal balance crankshaft-needs turned
eagle 6'' h beam rods-1 rod needs resized
srp dome pistons
$400 obo