sbc engine

[D1RT087]

could some one tell me what HP & TQ this engine will have?

SBC 350 60 over
3.48 scat stock replacement crank
5.7 I beam float rods
10.9:1 speed pro pistons
cam - lift .552 / .561 dur. @ 50 254 / 259 lobe sep. 106
Alum. heads - 190cc 64cc chamber 202 / 160 stainless valve straight plug
stainless steel full roller rockers 1.5
hurricane intake
holley 3310 750 carb

[Egoracing]

could some one tell me what HP & TQ this engine will have?

SBC 350 60 over
3.48 scat stock replacement crank
5.7 I beam float rods
10.9:1 speed pro pistons
cam - lift .552 / .561 dur. @ 50 254 / 259 lobe sep. 106
Alum. heads - 190cc 64cc chamber 202 / 160 stainless valve straight plug
stainless steel full roller rockers 1.5
hurricane intake
holley 3310 750 carb

You are really close to the specs of the 604 crate motor and should be in the 375-400hp area.

[D1RT087]

I was hoping for 450 HP . I for got if it helps the pistons is .125 dome. thanks for the replys

[sj valley dave]

Doesn't help at all..10.9:1 is just what it is...Actually better if you get it without domes...I'm assuming it is a solid flat tappet cam...I'd be guessing 400-425 hp...

[D1RT087]

yes the cam is solid, I hope that is enough HP to run with them at my track.

[C10]

The Hurricane intake is hurting you all over the curve, they are not a very good piece and have flow numbers all over the board. I would stick to a Vic Jr, or similar.

[D1RT087]

could some one tell me what HP & TQ this engine will have?

SBC 350 60 over
3.48 scat stock replacement crank
5.7 I beam float rods
10.9:1 speed pro pistons
cam - lift .552 / .561 dur. @ 50 254 / 259 lobe sep. 106
Alum. heads - 190cc 64cc chamber 202 / 160 stainless valve straight plug
stainless steel full roller rockers 1.5
hurricane intake
holley 3310 750 carb

I would like to THANK every one for there reply's. How could I get 450 - 500 hp and still use some of the parts that are listed. I would like to still use the heads and piston if i could. is the cam to big? I have to keep the carb they tech it.

[Egoracing]

2925 Victor intake would be a big help and have the heads cut to raise compression.

[sj valley dave]

I agree with Ego...If you swapped out the intake for a Super Victor and could cut the heads for more compression that cam would work a whole bunch better...With that cams profile and a little more compression, there's no reason you couldn't get 450-475 HP...What brand and model of heads are these?

[D1RT087]

the heads is prostar from j and c cylinder head exchange off of eBay. I know alot of people said not to buy cheap heads but i just wanted to get better heads than the stock 041 that i had. I could not afford $1000.00 heads. I am on an budget engine build. The engine we had before had .100 dome speed pro piston, speedway cam # 915-14104 and the 041 heads the rest of the engine was the same. I just thought that if i went to the .125 pistons , JR motorsports cam # 111 , and the bigger heads i would get at least 450hp. I seen in the c/t mag. where they built an street stock engine that made 450 hp for $2500 i think it was.

[D1RT087]

stock car driver if you are talking to me I did read what you said . Thanks for adding me to your f/b friends list. I did not know that going from a 2 barrel to a 4 barrel carb to an engine that it would add that much hp to it

[sj valley dave]

Going from a 500 4412 2 bbl to a 750 4 bbl you are really doubling your CFM...If you measure the air flow through a 2 bbl carb with the same amount of mercury a 500 2 bbl flows approximately 335-350 cfm. compared to a 750 4bbl...That is a big reason why a 390 cfm 4bbl will make more power than a 500 2 bbl..They are tested at different amounts of vacuum...It is like bolting on 50 hp, minimum if you have the cam and heads..

[D1RT087]

Is the prostar heads better head than the stock 041 heads. I paid $619 free s/h for the complete pair . The seller had all good feedback on the heads. I started to fix up he 041 but by the time i bought all new parts i would had just as much money in them as the alum heads. the rules says steel head but no one pulls any one. The full tear down on the motor is $1500.

[sj valley dave]

I agree with Parrot on that those heads are aluminum and you get some weight percentages, but as far as head flow, not that sure they are much better than the 041's, but even so, with 041's and a better intake you will be 450 hp or so...

[D1RT087]

Thanks for all the info. is the stainless steel roller rockers and HD stud girdles from skip white performance good engine parts?

[jsf74]

I'm prety sure most of that stuff is Procomp. Sometimes it works and sometimes it fails. The newer stuff is much better than the older stuff. You do get what u pay for though. All parts are NOT created equal.

[oldnelly87]

Thanks for all the info. is the stainless steel roller rockers and HD stud girdles from skip white performance good engine parts?

the stainless ones will be fine ive ran a set for the stainless ones for 4 years. their the procomps they sell i wouldnt trust the alumium pro comps on a soild cam.