LOTS Of USED PARTS FOR SALE

[SCP]

** SBC Dart 227 aluminum cnc'd 23 degree heads, fresh valve job & surface, bare, ready to assemble $1150.
** SBC New Brodix 18 degree castings, bare, no port work, $950.
** SBC 882 iron heads with lots of port work. May not pass your tech man? Fresh competition valve job & surface, screw in studs, 2.02 & 1.6 valves. $600 less springs & retainers.
** SBC Pro Action/RHS iron 200cc heads with port work. Complete w/new valves & springs. $750
** SBC World cast iron fully ported heads by Ron's Porting. Super Nice heads. Excellent heads for B-mod or IMCA. Fresh competition valve job & surface. $1150
** SBC Pro Action/RHS raised runner aluminum heads. Fully ported & polished, titanium valves, roller springs, Ti retainers. Fresh comp valve job & surface. Heads flow & will make some serious power for a modified or late model. Also has ported Edelbrock super Victor raised runner manifold & Jesel shaft rockers. Crower severe duty roller lifters & double taper push rods. $2900 for all.
** SBC USRA/USMTS Brodix Spec aluminum heads **** SOLD
** Callies 3 5/8" stroke 400 main crankshaft, JE pistons for 4.145" bore pistons, New Callies 6" rods.
Balanced. All really nice stuff. $1600
** Ten NEW JE custom dome pistons & pins for 4.030" bore 3.75" stroke & 6.125" rod. (cost $1100+) along with a almost new set of Oliver ltwt billet 6.125 rods. (cost $1300) Excellent B-Mod or A-Mod combination. Everything is balanced. $1250 for everything.
** Eight new Venolia pistons for 4.125" bore, 3.750" stroke & 5.850" rod. No pins. $350
** Eight new Diamond pistons for 4.125" bore, 3.625" stroke & 5.850" rod. New Eagle 3.625" 4340 steel crankshaft. $800 for both.
** Eight new Wiseco 18 degree dome pistons for 4.125" bore, 3.750" stroke & 6" rod. No pins. $375
** Like new Wilson gas modified or late model carb. $800
** New Gaerte/Shark gas mod or L/M carb. (cost $1200) $975 takes
** KSE hex drive tandem pump. $400.
** Winters Q/C rear cover with bearings. $70
** Q/C gears Winters & Q/Master 5.22, 5.37, 7.29, 7.52 ratios. $35/set
** Ace 9310 REM polished Q/C gears 6.31 ratio. $60
** MSD slip collar billet distributor. $175
** MSD part # 6601 HVC Black Pro box and MSD part # 8738 soft touch rev control. Looks new & cost $550 new. $275 takes both.
** Holley 1050 Dominator gas carb. $650.
** Taco 850 & 950 gas carbs. Billet base plates. Both rebuilt by Jim Evans & never run. $850 each.
** Crower stainless steel shaft rockers for Brodix 11X or 10X heads. $700
** Callies Magnum Plus crankshaft. 3 7/8" stroke, 350 main, 2" small journal rod. Crank would be $1600 new. It is standard / standard but it looks like it has been repaired on one rod journal. $650.
** Six #16 NEW 90 degree & 45 degree braided hose ends $100 for all.
** Champ aluminum Pro wet sump pan. Dent in bottom opposite pick up. Ran all year. $200
** C-Line Pro 10qt steel pan. ***** SOLD
** Aluminum water pumps $50-100
** SBC Edelbrock Victor intakes. $125-150
** SBC Dart fully ported intake. $475
** SBC Dart tall deck manifold, $200
** SBC Bow-Tie fully ported intake. $450
** Lots of near new modified coil springs $20-30
** New 350 shortblock. Has new JE dome pistons, new rings & bearings, freshly balanced & assembled.Eagle 6" H-beam rods, Crower/GM steel std/std crank. Fresh 4-bolt block. $2500
Call: Steve @ SCP 636-677-1320 or 314-374-5660 (cell)

[SCP]

updated today