Results 1 to 2 of 2

Thread: Selling Out

  1. #1
    Join Date
    May 2007
    Posts
    490

    Default Selling Out

    380” Short Block SOLD!

    359” Complete intake to pan SOLD!

    351” Complete Intake to pan $2200
    11.75:1, 351 cubic inches, Windsor style heads
    351W Marine Block, ARP Main Studs
    Stock Crank, 28oz External Balance
    5.956” Long Eagle “H” Beam Rods w/ ARP Bolts
    Icon Forged Std Bore Flat Top Pistons w/ Moly Rings
    Pro Products 28oz Balancer
    1964/65 289 Windsor Heads
    Manley 1.94/1.60 Race Flow Stainless Valves
    Extensively Ported
    Manley Dual Springs for Solid Cam
    Manley Moly Retainers
    ARP 3/8” Rocker Studs w/ 5/16” Comp Cams guide plates
    Speed Pro Full Roller Rockers
    Cast Aluminum Ford Motorsports Valve Covers w/ Left Side Breathers
    Speedway Cam
    Sig Erson Solid Lifters w/ EDM oil hole
    Ford Motorsports Billet True Roller Timing Set w/ 1 Piece Fuel Pump Drive
    5/16 x .080 Moly Push Rods
    Edelbrock Victor Jr Intake, ported and lightened
    ARP Oil Pump Drive Shaft
    Front Timing Cover w/ Stewart water pump
    Rear Sump 9 Qt Speedway Pan w/Gates
    Engine is currently assembled and has 18 nights of racing on it. No known problems.

    I have been asked by several for various parts of this engine to be separated out.
    Short block with pan and front cover $1650
    Heads with valvetrain and rockers $500
    Ported and Lightened Victor JR $250

    Short Blocks:
    Short Block #1 Sold!

    351W Short Block #2 $350
    .060 Over, KB Hyper flat top pistons with floating pins, 5.956” Cat “H” beam rods, Stock crank. Rotating mass is in ‘69/70 block but block may be too big after new hone is done. Includes another block that needs bored. Selling with the idea it will be put in the other block.

    351W Short Block #3 $350
    .030 Over, KB Hyper flat top pistons with floating pins, 5.956 Scat “H” beam rods. Comes with stock, 351W short block for crank and block cores. It’s a kit, you do the work!


    Misc Engine Parts:

    Quick Fuels 850 cfm Pro Series gas carb. Perfect condition, ready to go. $400

    Russell Baker 390cfm gas carb. This is the ultimate 390. Passed IMCA and NASCAR gauges. Included 2 sets of metering blocks. 1 set of high compression (12.5:1 and over) and another set for low compression (under 12.5:1). $350

    393 Stroker/351 Rods. Full set of used Scat 5.956” 351W stock length rods. These are “H” beam rods w/ ARP bolts, ready to use. $175 for the set.

    Single World Products Windsor Jr. Head. Ported. Bare Head, just a single leftover. $150

    Full set (plus 2 spares) of used KB/Icon Hyper .030 flat top pistons. Very nice condition. 351W pistons with pins. Been pin fitted and ready to put back into use. Set of 10 for $125

    2 Sets of Hartman/Comp Cams ultra lightweight plastic valve covers. Very cool pieces. Thick rail for a good seal, uses long bolts so no rail crush is possible. $40 for a set/$75 for all.

    Edelbrock/Roush intake. For early Yates style raised port heads. This will also work on a 351W with 351C 4bbl heads with a little work. Makes a neat combo. $300

    Edelbrock Torquer II 351W intake. Painted black, nice condition, no bad holes or threads. $100

    Pro Products Hurricane Intake (Victor Jr Copy). No porting, used 3 nights, like new. $150

    Stock Ford 351W cast iron intakes. Several to choose from. Mostly 80’s van/truck intakes. Good for stock class or street. $50 each

    sdllpark@netins.net
    Delivery is available/possible if needed. You buy the gas. This stuff is in SE Iowa.
    Last edited by LM14; 05-17-2013 at 12:53 PM.

  2. #2
    Join Date
    May 2007
    Posts
    490

    Default

    Updated Parts List and Prices!!!!

    SPark

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

All times are GMT -5. The time now is 03:30 AM.


Powered by vBulletin® Version 4.2.0
Copyright © 2024 vBulletin Solutions, Inc. All rights reserved.