Jay dikens, world product, vortec bowtie heads TRADES ?

[trickracing]

JAY DIKENS RACING ENGINES SBC STEEL TOP PROLINE HEADS 230 BEEN PORTED & FLOWED BACK AS UNTOUCHED CAST -FOR UNPORTED RULES, UP TO 600 LIFT ISKY FLAT TAP SPRINGS, 2.06 FERREA 6000 series ROLLER SPRING VALVES --STAINLESS & TITAINIUM VALVES, ANGLE MILLED DECK, 1.550 ROLLER RETAINERS & LOCKS, CHEATER HEADS, MADE ALMOST 600HP -8 RACES SINCE FRESH -COST OVER $3000 NEW --SELL $1800
----
VORTEC BOWTIE SBC STEEL HEADS, 2.02 FERREA VALVES, ANGLE MILLED DECK, RETAINERS & LOCKS NO SPRINGS -WAS SET UP FOR 1.450 FLAT TAP SPRINGS - 15 RACES SINCE FRESH-- COST OVER $1800 NEW --SELL $1000

---
WORLD PRODUCTS / DART SBC STEEL HEADS, 2.02 FERREA VALVES, ANGLE MILLED DECK-WORKS WITH FLAT TOPS OR DOMES,, 6 RACES SINCE FRESHENED -HAVE 1.250 SPRINGS, RETAINERS & LOCKS FOR THEM--COST OVER $800 NEW --SELL $400

10x 23deg hvh brodix raised runner sbc alum heads cnc ported & brodix intake ,best 23deg heads made -isky roller springs - 2.125 titainium valves, titanium 1.550 roller retainers & locks, t&d shaft rockers, 15 races on them since fresh , billet roller cam, moly push rods,,-cost over $7000 new sell or trade $3500

--------------------------------------------------------------------------------------------------------------------

15 deg brodix raised runner sbc alum (pontiac made for gm ) heads cnc ported & brodix intake with deck & intake spacer & new gaskerts -isky roller springs - 2.125 titainium valves, titanium 1.550 roller retainers & locks, t&d shaft rockers -arp head studs -2 races on them since fresh ,cost over $8500 new sell or trade $4000

--------------------------------------------------------------------------------------------------------------------

also have complete 362cu short block - lite weight older bowtie steel block, with billet mains ,bored for these 15DEG je dome pistons -set up for drysump or u can still run it wet sump - 6" honda journal h-beam rods, 3.520 callies lite weight 43lbs honda journal knife edge crank-drysump pan , billet roller cam, moly push rods, all balanced & ready to build - i was changing to the up stroke crank - but now goin to crate class !

-----------------------------------------------------------------------------------------------------------------

MANY OTHER PARTS : COMPLETE DRYSUMP FRT & REAR MNT SYSTEM - EXTRA DRYSUMP LINES , BUTLERBUILT TANK, COLMAN & 2 OTHER TANKS - 4 DRYSUMP PANS

MSD HEI SBC DIST MSD CAP ROTOR PICKUP


TRADES ACCEPTED : 604 CRATE MOTOR , ENCLOSED TRAILER, DUELLY, 4 WHEELER, NICE OPEN TRAILER ETC - LET ME KNOW WHAT U GOT

best way is to txt or call if u cant txt -- so we
can answer you - we dont get on here n check this
post much - in milton florida TXT OR CALL 850-426-2936 NO TIRE KICKERS PLZ! SERIOUS ONLY

[Racer's Auction]

Discover what veteran racers have known for years. Sell your unused racing parts that have set on the shelf for more than one year for fair market value and buy some parts that you can use in the upcoming year at one place,one time without all the hassles of annoying phone calls,shipping,tire kickers,etc. http://www.facebook....erracersauction 3/1/2014 Hamilton Co 4H Fairgrounds, Noblesville, In Contact us ASAP to reserve your lot numbers or Swap Meet Booth Lot numbers are limited so act today 317-443-0668, jwauctioneer@frontier.com