Tweet
I have a 2008 Rayburn over rail swing arm frame. It willl come with the complete tub & deck, nose, hard brake lines and fuel cell. The frame is straight, has never been bent or clipped and has approximately 35 nights on it.
Also have a list of parts that I'm wanting to sell. Many of the parts were from this Rayburn.
1 Wilwood 3/4" Master cylinder
1 New AFCO p/n 20010-1 aluminum shaft upper A-Arm
1 used AFCO 9-1/2" aluminum shaft upper A-Arm w/ screw-in ball joint
1 used 10-1/2" aluminum shaft upper A-Arm w/ bolt-in ball joint
1 used 10-1/2" aluminum shaft upper A-Arm (for bolt in ball joint)
1 used 9-1/4" aluminum shaft upper A-Arm w/ screw-in ball joint
1 used 14" swing arm
1 used 14-1/4†swing arm
1 used 14-3/4†swing arm
1 used 15-1/2†swing arm
1 New PPM 19" RF Blue Rocket lower control arm - PPM p/n 16519-S1PCRB
3 used RF lower control arms
1 used RF lower control arm w/ ball joint
1 used LF lower control arm w/ ball joint
1 used stud type lower control arm w/ heim and ball joint (16-3/4" from heim to ball joint)
1 21†J-bar
1 Wilwood Dynalite caliper w/ 1-1/2" pistons
1 new aluminum birdcage
3 used aluminum birdcages
2 Howe panhard bar frame mounts
1 Used panhard bar quickchange pinion mount
1 used power steering pump
1 Motor Mount Mid-Plate
2 17†Seats
1 Steering wheel w/ hex quick release disconnect, steering shaft, heims and couplers
1 Rayburn pullbar w/ quickchange brackets
Winters quickchange rear end complete w/ hubs, birdcages, driveplates and pullbar.
I had this all listed separately and it totaled $3455.
I am needing the space so I'm wanting to make somebody a deal!
I'd take $2800 for everything listed.
This is just a few parts short of being a roller. It's all good parts, I'd just rather someone be racing it than having this setting in my shop.
If you didn't need the rear end, I'd sell everything else for $1,250!
Located in Sikeston, Mo.
Can reach me at 573-427-1443.
Also have a list of parts that I'm wanting to sell. Many of the parts were from this Rayburn.
1 Wilwood 3/4" Master cylinder
1 New AFCO p/n 20010-1 aluminum shaft upper A-Arm
1 used AFCO 9-1/2" aluminum shaft upper A-Arm w/ screw-in ball joint
1 used 10-1/2" aluminum shaft upper A-Arm w/ bolt-in ball joint
1 used 10-1/2" aluminum shaft upper A-Arm (for bolt in ball joint)
1 used 9-1/4" aluminum shaft upper A-Arm w/ screw-in ball joint
1 used 14" swing arm
1 used 14-1/4†swing arm
1 used 14-3/4†swing arm
1 used 15-1/2†swing arm
1 New PPM 19" RF Blue Rocket lower control arm - PPM p/n 16519-S1PCRB
3 used RF lower control arms
1 used RF lower control arm w/ ball joint
1 used LF lower control arm w/ ball joint
1 used stud type lower control arm w/ heim and ball joint (16-3/4" from heim to ball joint)
1 21†J-bar
1 Wilwood Dynalite caliper w/ 1-1/2" pistons
1 new aluminum birdcage
3 used aluminum birdcages
2 Howe panhard bar frame mounts
1 Used panhard bar quickchange pinion mount
1 used power steering pump
1 Motor Mount Mid-Plate
2 17†Seats
1 Steering wheel w/ hex quick release disconnect, steering shaft, heims and couplers
1 Rayburn pullbar w/ quickchange brackets
Winters quickchange rear end complete w/ hubs, birdcages, driveplates and pullbar.
I had this all listed separately and it totaled $3455.
I am needing the space so I'm wanting to make somebody a deal!
I'd take $2800 for everything listed.
This is just a few parts short of being a roller. It's all good parts, I'd just rather someone be racing it than having this setting in my shop.
If you didn't need the rear end, I'd sell everything else for $1,250!
Located in Sikeston, Mo.
Can reach me at 573-427-1443.