WTB Parts to finish my car

[zayden88@sbcglobal.net]

looking for a few parts
Looking for some

Bilstein shocks

6.83 gear and 7.00 gear 31 Spline

block mount power sterring setup

powerglide transmission

Lead need about 2 or 300 lbs

White or black sheet metal

5 1/2 front springs 1000 1100

13 inch rear springs


This list will change as I'm working on the car thanks

[stock car driver]

I can ship you brand new 3rd members with those ratios in storage totes for 475.00 each. Those gears are deep and need to be set up correctly because the pinion is so small. I wouldnt consider buying them used unless from a good friend.

Ive got a add on here with block mount ps pump and mount with reservoir attached.

[stunner]

Give me a call Monday-Friday 8-7 and I can make you a deal as I have nmost all of what you need in either good used or new. 815-990-8865

[zayden88@sbcglobal.net]

stockcar

Let me know through private message on a deal for the power steering setup and possible your hydraulic throwout bearing and will that go on any style Chevy bellhousing

[stock car driver]

No need for pm.

My prices on those two items are already as cheap as youll likely ever find. Im going to start putting this stuff on ebay and moving it.

66jj on ebay if you want to watch for it there, Ill list it no reserve and let it go. Likely be after I get back from Alabama racing so 2nd week in Jan.

Jeff

heres the list again.

Used alum radiator 10 nights 28 inch. $75.00 3 nights $100.00

406 Complete motor. FRESH ALL parts only 6 nights old.…15.2-1, ported double hump heads, manley race flo stainless valves, performance valve job, 7/16 studs, roller rockers, Custom solid lift cam and lifters that are brand new.. motor was ran 6 nights, got hot 240 then freshened and cam changed. Made 401 hp with a 350 IMCA legal carb. 46lb 4340 steel crank, lw I beam rods with 7/16 cap screws, mahle 11cc dome pistons, kevco pan, Deck reinforced, lifter galley screened, lifter tray installed, edelbrock IMCA intake. All work and assembly done by Hatterman. $4500.00 obo

NEW Ohio 4340 47lb 434 crank. 4.00 stroke, 400 mains. Brand New. $650.00

NEW MAHLE flat top 436 pistons. For 4.165 bore, 4 inch stroke. NEW with pins locks $450.00

NEW MAHLE flat top 436 pistons. For 4.165 bore, 4 inch stroke. NEW with pins locks and rings. $550.00

USED Block mounted ps pump with attached plastic reservoir, serpentine pulley. $95.00

METRIC spindles with Spindle savers welded on. This is the way to go if you don’t run IMCA which made it illegal to weld the spindle savers on. I welded them on correctly… $40 each have several sets

New 9” 3rd members $425 shipped to you in a storage tote. Mini spool up to 650 ratio. Add 75 for full lw spool, Add 100 for lw ring gear. Any yoke, any spline. Usually ships next day. Assembled with solid pinion spacer and shims, not crush collar. NEW NEW NEW NEW

4.71 3rd member, lw spool, lw ring gear, 31 spline. $250

Scatter shield lightened IMCA legal $125

ATTENTION Custom manual transmission. Run either high or low!!! Coarse input spline, T 10 manual trans. In oem Richmond case. 2 speed straight cut gears, lw rotating assembly, shift on the fly with no clutch, 1.03 and 1.00 gear. Gives you 2 gears at the track all the time to choose from!!! $1200 with slip yoke you need to put on your driveshaft as it uses a large one! If you have 5.29 in the rear end low is 5.43 so you always have two gears to race in. you can shift any time you breath the gas, no clutch needed or issues.

USED 3 disc tilton clutch. With brand NEW discs in box. $350.00

USED tilton 3 disc clutch with used discs, 4 nights on them. $275.00

USED Quarter master 3 disc. 3 nights on discs. $275.00

Hydraulic throw out brg. Quartermaster 100. Qm100 is the part number. No bolts to adjust, sits on ball in bell housing. $95

RHS vortec heads. Ten degree locks, fereah valve, 5 nights. Bolt on and go!! $600

Aftermarket Patriot Performance Vortecs, manley race flow valves, milled to 56cc 10 degree locks springs, 17 nights, then 2 nights on complete rebuild. Bolt these on and go!! $600

461 double hump heads, 2 nights since freshened with good perf valve job. Screw in studs, plates, big springs, stainless valves. READY to bolt on and go today. No porting. All good parts. $400

New Gun drilled Axle. 31 spline. 29.5 long. $65.00 NEW

Turbo Wing. High polished ss over the cab wing for trucks towing big trailers. Easy to mount in 5 minutes. $500 like new easy to install! Can email you pics.

400 4 bolt block, standard bore $400

NEW Pro/Race pro series race balancers. SFI 18.1. NEW in package. ($229.99 from JR) Sell $100.00
……… Link to balancer info…… http://www.pro-race.com/prorace.htm

Keith black .100 dome 383 pistons. 4.030 bore, on nice polished x rods, 4-6 nights old, childs albert moly rings. Nice package to put in your block. Balanced and with balance card. $250 all.

Quadra jet intake manifold. Modified plenum area thru 4 3” holes gain of over 15 hp from weind 7547 proven on back to back dyno run by myself, no smoke and mirrors. $200 each. Pics on www.jnjfab.com in the for sale section.

IMCA sport compact. NEW Race ready car. See at www.jnjfab.com 93 grand am gt h.o 180 hp, manual trans, new head, new time chain, new struts. $3000

16” Afco rear springs, 5 inch. 120, 125, 150, 175. All just rated. $25.00 each

New MSD 6AL in box. $210.00

Kirkey bolt on shoulder supports. PAIR $25

Box of HEI distributors. Included 5-7 dist, at least two mds modules, coils, lots of good parts. $75.00
4 - 17” 2008 dodge dually steel wheels. $75 each. Dealer gets 280 each

NEW roller rockers 7/16 stud 1.6 ratio. $75 New in box clearanced for big springs. Red alum bodys.

EMAIL JEFF jnjfab@live.com