Michael Page

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • luke81
    Senior Member
    • Feb 2013
    • 104

    #31
    This is the type of violation where i have a very hard time believing it was intentional just because you have to know they're going to check that.

    Comment

    • dirt farmer
      Senior Member
      • Apr 2016
      • 100

      #32
      The reason I was thinking someone made a mistake was I had heard from someone there that only one spring checked wrong.

      Comment

      • TerryM
        Senior Member
        • Apr 2011
        • 3902

        #33
        They’re saying they removed a specific amount of shims (washers?), but accidentally left one too many in.

        Comment

        • Jking24
          Senior Member
          • Oct 2017
          • 1519

          #34
          So curiosity was killing the cat here. So i looked it up the valves are allowed to be shimmed a maximum of .020" to get seat pressure back after valve seat machining during a rebuild the seat pressure is 101# plus or minus 4# so basically 105#. If one takes the press release for its literal wording than it's must have measured wrong. But the two are directly related so if you told a engine guy your seat pressure was wrong he would tell you thats because your installed height is wrong. So to say the installed height is wrong could be interpreted as it's actually wrong or the spring pressure is incorrect since it is what controls that spec. Not trying to argue with anyone just thinking out loud

          Comment

          • ZERO25
            Senior Member
            • Aug 2018
            • 5240

            #35
            Whats kinda strange, he won the big crate race at Cochran just a couple months ago! Did they not check it then or was this a new motor?

            Comment

            • dirt farmer
              Senior Member
              • Apr 2016
              • 100

              #36
              Originally posted by ZERO25 View Post
              Whats kinda strange, he won the big crate race at Cochran just a couple months ago! Did they not check it then or was this a new motor?
              It was checked.And.was good, not sure but heard it was same motor just had it gone through.

              Comment

              • fastford
                Senior Member
                • Dec 2008
                • 4059

                #37
                Originally posted by billetbirdcage View Post
                I'm pulling numbers out of my arse, too lazy to look up the correct numbers

                The install hieght is spec'ed like at 1.78 +/- a certain amount like .020
                The spring pressure has a max pressure of like 110#

                So while possible that a spring is out of spec and has 115# at the 1.76 to 1.8 install height allowed, it's not very common. They know the range of the springs and have rules set so it doesn't happen often, but it is possible. The pressure rule is more for non stock springs and springs that look just like the stock ones but are slightly stiffer. Many of those have real similar seat pressures but the open pressure is higher and hard to check without pulling spring off head to check the full range of the spring not just the on head test for seat pressure with a pull type on head spring checker.

                Again, just going off the report/post why he was D/Q'ed it seems he was out of spec on the install height, I didn't see anything posted about pressure. I'm not trying to throw anyone under the bus but if it was indeed a install hieght only infraction, then that was done by someone not taking the time to do it right or didn't have the proper tools to set it correctly. Also not saying it was done on purpose either, could been a mistake, but with things like that I would figure a decent team doesn't make mistakes like that, when it's one of the first things checked
                springs out of spec are more common than you think with these cheaper springs , thats why builders like Brad go through a bunch of springs just to get a set like they want that will comply with tech , i have bought a lot of the throw away,s from a local builder for half price that under normal applications were fine , this is the problem with a crate engines , if you want the very best LEGAL engine , you have to pay the piper .......

                Comment

                • billetbirdcage
                  Senior Member
                  • May 2007
                  • 2020

                  #38
                  Originally posted by fastford View Post
                  springs out of spec are more common than you think with these cheaper springs , thats why builders like Brad go through a bunch of springs just to get a set like they want that will comply with tech , i have bought a lot of the throw away,s from a local builder for half price that under normal applications were fine , this is the problem with a crate engines , if you want the very best LEGAL engine , you have to pay the piper .......
                  I've spent 2 full days on the Spintron for the 604, if you want to believe that the 5 or even 10# variance you see in springs makes a difference. . . . shrugs.

                  Most people would be shocked to what has an effect and what doesn't

                  Comment

                  • 84wedge
                    Senior Member
                    • Sep 2020
                    • 2094

                    #39
                    It amazing that would be such a big advantage in such an old car. People are constantly talking about new cars being faster, and the fact that even new Mastersbilt aren't faster makes it more amazing one 10+ years old crossed the line before a new XR1. There was an article in Dirt Late Model Magazine about Page years ago and one of his sponsors talking about how he was one of the few drivers left who could cut the front clip off the car and rework it all by himself. I wonder it Tader knows about the mods Page has made to that chassis.

                    Comment

                    • Jking24
                      Senior Member
                      • Oct 2017
                      • 1519

                      #40
                      Originally posted by 84wedge View Post
                      It amazing that would be such a big advantage in such an old car. People are constantly talking about new cars being faster, and the fact that even new Mastersbilt aren't faster makes it more amazing one 10+ years old crossed the line before a new XR1. There was an article in Dirt Late Model Magazine about Page years ago and one of his sponsors talking about how he was one of the few drivers left who could cut the front clip off the car and rework it all by himself. I wonder it Tader knows about the mods Page has made to that chassis.
                      Not knocking anything Paige has done but just because it's a good crate car doesent mean it can compete with an open motor in it. Most guys in crates get caught up chasing the newer setups and their car couldn't spin a tire with the old stuff so alot of it is all for nothing.

                      Comment

                      • NeedforLM$peed
                        Senior Member
                        • Dec 2020
                        • 1637

                        #41
                        Originally posted by davis2902 View Post
                        Was he dq'ed from Thursday portion as he was running same motor?
                        No but that might've been something they didn't check considering it paid much less on Thursday than Saturday.

                        Lots of good insight and info.
                        2021 race count
                        6 events

                        Comment

                        • chupp n bloomer fan
                          Senior Member
                          • May 2007
                          • 11526

                          #42
                          Originally posted by Jking24 View Post
                          Not knocking anything Paige has done but just because it's a good crate car doesent mean it can compete with an open motor in it. Most guys in crates get caught up chasing the newer setups and their car couldn't spin a tire with the old stuff so alot of it is all for nothing.
                          And I’m sure it’s been totally updated and has all the latest stuff. Not like it’s as is from 10 years ago for sure.
                          Up in the air who my next “favorite” driver is. Really losing hope on Bloomer getting anywhere back to “normal”.

                          Comment

                          • MasterSbilt_Racer
                            Senior Member
                            • May 2007
                            • 14324

                            #43
                            ^^Page was saying in a DOD article last year that nothing was done to that car. I'm not buying it either. Even in crates. But, what Jking said has some merit as well.
                            Modern Day Spec Wedge Racing

                            Comment

                            • fastford
                              Senior Member
                              • Dec 2008
                              • 4059

                              #44
                              Originally posted by billetbirdcage View Post
                              I've spent 2 full days on the Spintron for the 604, if you want to believe that the 5 or even 10# variance you see in springs makes a difference. . . . shrugs.

                              Most people would be shocked to what has an effect and what doesn't
                              i guess i am a bit behind the times billet , tell me how you can tell the difference a spring makes on a spintron ? , now i can see a dyno , but i thought a spintron is more for breaking in an engine , not evaluating if 10# of seat pressure makes a difference in the performance of the engine.....

                              Comment

                              • billetbirdcage
                                Senior Member
                                • May 2007
                                • 2020

                                #45
                                Originally posted by fastford View Post
                                i guess i am a bit behind the times billet , tell me how you can tell the difference a spring makes on a spintron ? , now i can see a dyno , but i thought a spintron is more for breaking in an engine , not evaluating if 10# of seat pressure makes a difference in the performance of the engine.....
                                Spintron is not for breaking in anything, it's to measure valve train performance and stability. The valves go out of control at 6750 rpm, anything you change shows up on the graph as far as valve bounce, lofting, spring surge and just generally how well it follows the cam profile are different RPM's.

                                What I'm saying is those Good/matched/higher pressure stock valve springs that have say 8# more pressure then the others:

                                1: once the engine runs at 1200 idle RPM the valve spring has cycled 10 times a second. Do you really think it is still the same 8# higher then the other springs? Take one of those new springs and cycle it 10 times in a vise and retest the spring and tell me if it's not about the same as the other springs or didn't lose a ton of the 8# advantage? (this isn't also getting the spring hot to 200+ degrees)

                                2: Pressure isn't the only factor on controlling the valve, sometimes less pressure can be more stable at times if the right things are met. There is a reason Cup engines only have 90/100# of seat pressure and can run 10K RPM, it's not all about pressure.

                                3. Now a 604 makes no power at the 6750 RPM anyways, but getting more RPM allows you to run more gear if needed and not destroy the engine or allows you to chip the engine higher. My point is that those match springs or slightly higher poundage you pay a premium for have no real effect on the valve train going nuts and trying to self destruct at 6750.

                                4. When you have weak push rods, rocker studs, rockers and etc, adding unneeded spring pressure can just make flex/lofting/surge worse and actually make the valve train go unstable earlier (not always but many times). Many times it makes the valve not follow the cam profile and hurts power.

                                Obviously your not allow to change any of those things (only stock parts) but testing that stuff showed what mattered and what didn't. Not giving away any results but just maybe having a shorter install hieght (min allowed) and a weaker spring (low end of the springs ranges) could allow you to stay under the max seat pressure but since the spring is closer to coil bind, it surges less and increases the RPM before it goes nuts (again just a scenario)
                                Last edited by billetbirdcage; 01-20-2021, 07:30 PM.

                                Comment

                                Working...
                                X