Spring smasher #s

[keeks]

Where else would a bump stop go?

[Jking24]

15d i think your over complicating it. Just as mb racer said nothing has changed except how we look at things. if you don't have known numbers from your chassis builder to start with. Setup car traditionally measure ,smash to those cc than record data do not change it race it and adjust accordingly.

[Jking24]

I will add this that 3.75 number is petty high on average that doesn't mean it's wrong though

[cjsracing]

evidently I'm cheating then. I don't have a bump stop on the suspension, I have one on the shock rod. Guess next time I see Randy Anderson at the track I'll get his take on this.

Thanks for pointing it out!!

Haha. The first thing Randy said to me at the Tipton Deery show during pre-race tech was "You don't have any bump stops or stacked springs on the car right?"

[hunterracing]

What’s a good number for standard rr spring 225 at static ride height or the fronts for smash numbers

[billetbirdcage]

You can't just give numbers for every car as motion ratios and % are different between a lot of cars so they can't be used as a general number for all cars.

The static RF numbers between a blue/grey rocket maybe be an easy 100# difference from an XR1 and more on other cars. Fronts will typically be way closer between different cars then the rears can be. Some may be really similar and others could be 200# different at static.

Just to show you on the RR you asked about, I've been as low 175# and as high as 700# so.....

[15D]

Haha. The first thing Randy said to me at the Tipton Deery show during pre-race tech was "You don't have any bump stops or stacked springs on the car right?"

Hmm......I might have to come up with a convenient mis-statement of the truth should I bump into Randy.

[hunterracing]

You can't just give numbers for every car as motion ratios and % are different between a lot of cars so they can't be used as a general number for all cars.

The static RF numbers between a blue/grey rocket maybe be an easy 100# difference from an XR1 and more on other cars. Fronts will typically be way closer between different cars then the rears can be. Some may be really similar and others could be 200# different at static.

Just to show you on the RR you asked about, I've been as low 175# and as high as 700# so.....

I was just curious kinda figured wouldn’t be same for every car or driver

[15D]

15d i think your over complicating it. Just as mb racer said nothing has changed except how we look at things. if you don't have known numbers from your chassis builder to start with. Setup car traditionally measure ,smash to those cc than record data do not change it race it and adjust accordingly.

If I run any less the nose starts plowing. I set the car up old school last week and it was slightly tight according to the driver, but sitting in the stands it looked slightly loose (an ongoing, decades worth, of discussion between us, was it actually loose or did you over compensate and it felt tight.)

[riddle28]

so just so im straight. my car is an 09 so no smash numbers. I set my car up conventionally, lets say rf wheel weight is 500 lbs. do i take that spring off the car, put it in the smasher and run the smasher to 500 lbs and that is my center to center or do i run the smasher to my static center to center #s i measure on the car and let the static smasher number just end up where that is?

[fastford]

If I run any less the nose starts plowing. I set the car up old school last week and it was slightly tight according to the driver, but sitting in the stands it looked slightly loose (an ongoing, decades worth, of discussion between us, was it actually loose or did you over compensate and it felt tight.)

a simple piece of white tape wrapped around the top of the steering wheel with the tires strait will help solve your debate on the tight loose thing........

[MasterSbilt_Racer]

so just so im straight. my car is an 09 so no smash numbers. I set my car up conventionally, lets say rf wheel weight is 500 lbs. do i take that spring off the car, put it in the smasher and run the smasher to 500 lbs and that is my center to center or do i run the smasher to my static center to center #s i measure on the car and let the static smasher number just end up where that is?

The second option is correct.

[7uptruckracer]

Take your race ready setup. Go over to it with your tape measure. Measure every coil over center to center aka eye to eye aka pin to pin. Write down those measurements. Take each spring off one at a time. Load it into the smasher and smash it to your written down pin to pin. Write down the spring load number the smasher gives you. That is your static spring preload. Lets say this for example is your RF. At Race ready your RF Pin to Pin is 18" You load it into the smasher and it reads 600lbs. Write that down. You know your car travels say 4.5". So take your machine and write down your spring load at 13.5" pin to pin or eye to eye whatever you want to call it. That is your spring load at dynamic. Lets say its 2100lbs. YOu can with that info change your spring. Take a softer one. Smash it down to 18" and make sure you set the collar until it reads 600lbs you could then if you wanted bolt it back onto the car and if you put it back on the scales all your numbers will be exactly how it was when you did it" old school" what you will find is if you put that softer spring in the smasher reset it to 600lbs at 18", and then take it to 13.5" you won't have at much dynamic load because you went softer. So what you can then play with is spring rubbers, Bump stops, etc. You have a static and dynamic baseline. You can do alot of manipulation once you have those two.

so just so im straight. my car is an 09 so no smash numbers. I set my car up conventionally, lets say rf wheel weight is 500 lbs. do i take that spring off the car, put it in the smasher and run the smasher to 500 lbs and that is my center to center or do i run the smasher to my static center to center #s i measure on the car and let the static smasher number just end up where that is?

[billetbirdcage]

Take your race ready setup. Go over to it with your tape measure. Measure every coil over center to center aka eye to eye aka pin to pin. Write down those measurements. Take each spring off one at a time. Load it into the smasher and smash it to your written down pin to pin. Write down the spring load number the smasher gives you. That is your static spring preload. Lets say this for example is your RF. At Race ready your RF Pin to Pin is 18" You load it into the smasher and it reads 600lbs. Write that down. You know your car travels say 4.5". So take your machine and write down your spring load at 13.5" pin to pin or eye to eye whatever you want to call it. That is your spring load at dynamic. Lets say its 2100lbs. YOu can with that info change your spring. Take a softer one. Smash it down to 18" and make sure you set the collar until it reads 600lbs you could then if you wanted bolt it back onto the car and if you put it back on the scales all your numbers will be exactly how it was when you did it" old school" what you will find is if you put that softer spring in the smasher reset it to 600lbs at 18", and then take it to 13.5" you won't have at much dynamic load because you went softer. So what you can then play with is spring rubbers, Bump stops, etc. You have a static and dynamic baseline. You can do alot of manipulation once you have those two.

I'll add to this:

1. You will also want the other compression (or rebound loads on LR) travels besides just the static (18") and the max dynamic (13.5")

2. The other travel numbers: (non 18" and 13.5") Early 1" increments are fine as long as the spring assembly is linear, but once it goes non linear: You will want at least in 1/2" increments and most likely way finer like 1/4" or 1/8th's if possible. Non linear: just means when rate changes due to rubbers, dual stage, or bump spring/stop engagement.

3. On certain coilovers, you will want to get an idea of rounds to change loads a certain amount so you don't have to pull just to make an adjustment at the track. Others you may want to install rubbers and have a basic idea where that takes the dynamic loads.

[7uptruckracer]

Great info! I just didn’t want to fry his brain lol! It’s astounding how much you can manipulate things. Especially tech rules with the smasher now that’s I’ve gotten involved heavily with it. I wouldn’t be surprised if we end up with a minimum ride height or block height soon. I take 1” just to make sure everything is kosher then when I get to a “secondary spring rate” I mark every 1/8-1/4. The funny thing is you can do all this work and still not know what it needs in race conditions it’s just more tools

I'll add to this:

1. You will also want the other compression (or rebound loads on LR) travels besides just the static (18") and the max dynamic (13.5")

2. The other travel numbers: (non 18" and 13.5") Early 1" increments are fine as long as the spring assembly is linear, but once it goes non linear: You will want at least in 1/2" increments and most likely way finer like 1/4" or 1/8th's if possible. Non linear: just means when rate changes due to rubbers, dual stage, or bump spring/stop engagement.

3. On certain coilovers, you will want to get an idea of rounds to change loads a certain amount so you don't have to pull just to make an adjustment at the track. Others you may want to install rubbers and have a basic idea where that takes the dynamic loads.