Roll Centers on G-Body

[stock car driver]

stockcar im still tryin to figure out how there getting rc below ground. from what i know about rc's it would be impossible with the lowers level. maybe i dont figure it right cause i never use it, since i work with LM's and we pay big money for chassis thats already had all this figured.

I cant figure it out either. Unless their lowers have a lot of angle its impossible...

But apparently they dont want to discuss it. Whatever, maybe its why my cars handle so well Im doing everything different, lol..

[stockcar5]

jeff..if your lower a arms are level and your uppers slope 1/8" down where does you roll center end up?

[stock car driver]

jeff..if your lower a arms are level and your uppers slope 1/8" down where does you roll center end up?

1\8 towards the tire like your saying yours were? Ive said twice not sure if you just go out away from the car with the upper line until it intersects or what??

My program takes all the front end numbers and I dont have oem like I said. Ill have a frame on the jig this week and might measure it up, Im burried with cars to build, garage addition on my house, bathroom remodel upstairs, my jeepster is torn apart in my racing stall so Ive gotta get 4 link rear 3 link front and my new axles struts in it etc. BUSY..

If you want me to lay it out your way and just run it way out till it hit I could lay it out on my shop floor in 5 minutes tomorrow.

I just worked on your old chassis that chad bought and Ill say this, I havent got a lot of faith in your car modification techniques. He couldnt get as much camber on the rf with your a arm mounts to get near what I run on the left front!

The whole construction of that car defies logic, reason and triangulation.

Youve always got some really nice looking alum and bodys though!

[stockcar5]

i dont lay anything out except for the car centerline. then measure all points and input them into the program and it calculates it. same way all roll center software works.

[stock car driver]

i dont lay anything out except for the car centerline. then measure all points and input them into the program and it calculates it. same way all roll center software works.

Yours obviously isnt working. Simple layout proves that for ya. Try it some time its really easy.

[steveshawjr]

heres some stats for yeh

Points Championship 1994, 1998, 2001, 2004
Mid Season Championship race winner 1994, 1995 Ridgetown 1996 1998 1999 2002 2007
Season champion race 1996, 1998, 2001, 2004, 2007, 2011
Most Checkerd Flags 1994 1995 1996 1997 1998 2001 2002 2004 2007 2010 2011
Fan Favourite 1998 2001 2002 2004 2007
total 311 wins... 100 a-main wins
updated Sept.11th 2011
Did not race in 2003, 2008, 2009

Steve Shaw Sr.

[stock car driver]

heres some stats for yeh

Points Championship 1994, 1998, 2001, 2004
Mid Season Championship race winner 1994, 1995 Ridgetown 1996 1998 1999 2002 2007
Season champion race 1996, 1998, 2001, 2004, 2007, 2011
Most Checkerd Flags 1994 1995 1996 1997 1998 2001 2002 2004 2007 2010 2011
Fan Favourite 1998 2001 2002 2004 2007
total 311 wins... 100 a-main wins
updated Sept.11th 2011
Did not race in 2003, 2008, 2009

Steve Shaw Sr.

Whats a fan favourite? Is that like coopitition that Larry McReynolds says?

So you set your car up on a shaker or pull down machine? None of those stats make sense Jimmy Johnson was the champion most of those years.

[steveshawjr]

you must have some timers lol you asked where we where winning at i put up our stats

Fan Favorite Driver award lol


32 years of this crap without any fancy equipment here dont even own a set of scales .... Never once did centers or anything like that ...

Steve Shaw Sr

[4bangerhotrod]

so have you raced at the same track every week for 20 yrs. thats what your stats are showing

[stock car driver]

you must have some timers lol you asked where we where winning at i put up our stats

I asked WHERE you were winning?

You didnt answer that. lol..

Still not sure now why your posting in this thread at all, now you claim to have never used scales or measured anything. But earlier in this thread you were saying we needed pull down machines, lol.

You must be buddys with Ego, he never answers anything directly and most of his posts are useless.

[steveshawjr]

now if you noticed he put steve shaw sr because my dad is the on that put them posts on .

now i never did claim i used a pull down rig for that matter you better go reread what is posted . i simply said that is what the big thing is now..

[stock car driver]

now if you noticed he put steve shaw sr because my dad is the on that put them posts on .

now i never did claim i used a pull down rig for that matter you better go reread what is posted . i simply said that is what the big thing is now..

Yeah on tv Nascar shows, lol...

[hogracer3d]

I wanna see a pic of JJ's wife, if there is one (which I doubt), but I'd accept a cancelled child support check.....

[stock car driver]

I wanna see a pic of JJ's wife, if there is one (which I doubt), but I'd accept a cancelled child support check.....

Man your a loser.

Join my fan page on face book and like the 1150 others on there youll know what Im up to most of the time, including some of the family vacations we take each year.

[sportmod224]

Hey Jeff, I have a couple questions I would like to ask you if you have time about the front spring set. Is there any chance we can talk on the phone instead of messaging back and forth on here? Thanks