Tilton clutch

[dannyracer6]

I have a tilton Maxim single disc 7.5 clutch on a quartermaster flywheel, bought it used but in great shape. did not get a throw out bearing with it or attaching bolts to flywheel. What throw out bearing do I use on this with a stock pinto 214 tranny. I think the bolts are the short ones. Need to get a throwout. Thanks.
Will a standard starter work with this flywheel, never used one of these before. sorry, it is a tilton sonic Mach 1.

Dan

[let-r-eat]

measure from back of block to pressure plate fingers. I usually lay a straight edge across the pressure plate fingers and measure to back of block at bellhousing face. Then stick straight edge over bellhousing and measure back to front of clutch fork held by hand where you want the clutch to start disengaging. Subtract the bellhousing measurement from pressure plate measurement and a quarter inch. Then look for the length throwout bearing you need.You can even put the stock bearing on your fork for the measurement and then that will give you the +1/2 or +3/4 or whatever you need.

[dannyracer6]

thanks....does the starter care what flywheel it engages. ?

[RACEMAN]

thanks....does the starter care what flywheel it engages. ?

Yes, I think it must be matched. It will be helpful if you know how many teeth are on the starter ring of the flywheel. Should be able to determine the correct starter to use.

[car62]

a stock starter or the smaller ranger starters(gear reduction)work with the 132 teeth flywheels

[dannyracer6]

thanks eric. I put the two flywheels together and they match as well as the teeth. Also the taller t/o bearing works with the small ford tranny, they sell it at Speedway in the pony section.

Does anyone up there use the alum. Esslinger intake for the iron head. I have a D port and an Oval port and I do not use them. Both in great condition. It is the little flat one. You seem to know a lot of racers up there.

Dan

[dannyracer6]

this tilton I have has a 135 tooth flywheel, my stock flywheel is 132, Looks like the tilton will not work unless I get an aftermarket starter. My old gold star use a stock starter. go figure.

[Robertms]

Intakes

thanks eric. I put the two flywheels together and they match as well as the teeth. Also the taller t/o bearing works with the small ford tranny, they sell it at Speedway in the pony section.

Does anyone up there use the alum. Esslinger intake for the iron head. I have a D port and an Oval port and I do not use them. Both in great condition. It is the little flat one. You seem to know a lot of racers up there.

Dan

Just sent you a private Message on intakes. Let me know if you got it. Robert

[car62]

thanks eric. I put the two flywheels together and they match as well as the teeth. Also the taller t/o bearing works with the small ford tranny, they sell it at Speedway in the pony section.

Does anyone up there use the alum. Esslinger intake for the iron head. I have a D port and an Oval port and I do not use them. Both in great condition. It is the little flat one. You seem to know a lot of racers up there.

Dan

yes there are a few up here that can run those intakes...and i actually know a couple people looking

[crcltrakr]

Tilton

Danny;

Somewhere along the line I recall an expensive lesson about matching the T/O bearing face to the style of pressure plate (3 adjustable arms vs diaphragm type). Some t/o's mave a flat machined face, others a radiused stamped face, again a call to tilton might be in order....

[dannyracer6]

jerry, I figured out that I have to have a special starter for this 132 in flywheel, and by the time I buy one of those, I would be better off to just get a gold star and use the oem starters. I got this clutch assembly thinking it was like the gold star, well it is not. so I will just sell it to someone who has the stuff to go with it. I will run the oem with an alum flywheel. Cheaper, in the long run.


dan

[car62]

Dan,we have a very good shape amuminum flywheel for sale that takes regular size clutch

[dannyracer6]

tilton

Message me a price. I cant use this tilton without a starter. dont want to get too spendy on this thing.
Dan

[return to dirt]

danny,
ford used drives with different tooth counts. you might be able to just change the drive and use a stock starter. changed a lot of them years ago before starters became so cheap. what does the quartermaster/tilton combo weigh? did you sell your nissan stuff yet?

olin

[dannyracer6]

Yes, I did. that tilton stuff is about 8# or so. super light. it is a 135 tooth quartermaster plate. I would really like to use it, but cant afford the starter. Now I could probably change the drive. what do I look for in a drive. I have a reman stock starter.

Dan