running a saginaw in a mod up's and down's

[JustAddDirt]

really

bonk_87

I dont have a dog in this fight, but to ask a question, get some responses, and attack a member that is really stating a facts, is not really the way to get assistance in the matter at hand.
Do what you wish, but you are better off in the long run to sell the multipul tranny's you have and the clutches you have and fund the racing unit.
If everythig works with the 3 speed than great you got lucky, but if it doesn't and you break a trans or a bellhousing, rip out the x crossmember in the car, destroy a driveshaft, rip off the pinion, and yoke, puncture a hole in fuelcell, and leak out fuel everywere (maybe catch fire). Also, if you have a tranny or clutch explosion injure your right leg.. Just stating a harsh reality, because I have seen it happen. Just think if you are hurt bad enough and you cannot work, was it worth it? Probably not.

I know it is hard to fund stuff, but think about the repair costs ahead of time. Especially with what can possibly happen on what I have written above, sit out a while and buy the trouble free parts. You will thank yourself in the long run.

[charcoal01]

I'm with the guys above me bonk. Maybe he said it in a way you didn't like but you really should try to run a race transmission if you can. I had a stock transmission lock up on me, without any warning. I was running a 3 speed in my 3000 lb pro stock and luckily it was in hot laps.almost put me in the fence and might have got really hurt if it was in a race. Save yourself the frustration and get a transmission made to handle that nice motor you've got.

[balljoint]

Do what you can afford to keep racing. Work on the setup and get the new tranny later.

[MM90]

I'm one of those if you can do it cheaper then that's how I do it. But like some have said above, it will probably end up costing you in the end. Used Brinn's that have been freshned are around $900. I hope you can make it work, and I hope you do well with it. But buy a Bert/Brinn/Falcon/Racegator/Mitchell as soon as you can.

[JustAddDirt]

yep there is always a way the whole point was just useing up what i have in my shop insted of letting it collect dust i already have 2 light weight clutch setups that are pretty much like new all the wanna be hot shots can go eat there steak dinner and go spend there $ or there sponcers $ on high $ parts and bold them on they just dont wanna get there hands greasy and put a little work into somthing i work my ass off just to do what i love doing and work till my hands bleed then you got some smart rich ass trying to tell you how to do it with bolt on parts id rather crank up the music spend hours in the shop working on my race cars than go out eat dinner and listin to some cranky ass rich wife i realy dont care what they say bout the weight they try to save my engin dyno at 610hp 358limit late model enging going in this mod and im not worried bout a little extra weight haveing a clutch in the car when you can only run a 8inch wheel you got thes rich guys out there running there money around a track that the car cant handel all there high$ parts and flying apart spinning tires and waveing to the in field with there left front tire all they do is show off and lose track time anyway i like my car with all 4 on the track thats the way it should be ive seen so manny hot shots spend ton of money and get there a$$ takein down by back woods racer manny times where i come from i kill my food drink my beer and work my ass of just to race on the weekends mabey someday ill get some sponcers to help me out with somthing i work and also work on my cars pretty much my self i do all my engine building my self just to save money ben building engines for 15years dirt and drag and non never left me down other than a faultie part so MR know it all kan kiss my hard workin poor A$$ you know what i meen

Talking like that, good luck getting big $$$$ sponsors, or anything for that matter. Just sayin.
I am not rich, nor do I clain to be. But attitude, and presentation has alot to do with who gets sponsorships.
Just an observation.

[jsf74]

No wonder you have no sponsors or anyone willing to help. You claim to race sprinters and have three cars but can't afford a good trans. I call bs. Don't flame someone who you asked advise from sometimes the truth hurts.

[dirttrackrocker]

I wasn't being a smart a$$, I was telling you the cold hard truth and trying to save you money. Judging by your spelling and grammar, I'm guessing you aren't smart enough to take the advice anyway. Good luck, just remember when you end up spending twice as much trying to make inadequate stuff work, someone tried to help you.

[jsf74]

Lol cant fix stupid

[chapa9]

If you think 610hp is a lot in a mod sell the mod now and save ur self the time. You can spend all the time in the shop saving a dollar but bolting up parts that will not compete is wasting your time and simply dumb. Like said already if ya can't afford a used Bert/Brinn/Falcon sale the mod now. Save your self time and money and get a good tranny.

Before u blast me I work 50+ hrs a week not a rich kid or got a rich wife got 2 kids all the regular stuff. I spend my money and time wisely. After wasting money on direct drie glides I waited till I could get a falcon before I ran my mod again. Anything else is a waste of time. I've been there done that.

[bonk_87us]

whatever

all yo haters are the stupid ones that cant be fixed any way the whole point was to run what i have not trying to be cheep bout it just for someone comeing out and judging someone whit a smart a$$ coment saying if you cant by a raceing trans you shouldent even be raceing had nothing with me not haveing the money for a race tranny i have the money to buy one but the whole point was i already have all the stuff to set it up with a saginaw so there was no money to spent there only turning the tail shaft down and that dident even cost anything and also i dont clame i have 3 cars i know i have them work on them all the time top it all off i realy dont care if i ever get a sponcer anyway most of them want you to do it there way and ive made it this far with out one so ill keep doing it and yea i did buy a brinn tranny tody not because all you hatters and you know what im just gonna let it set on the work bench keep doing what i was doing with the saginaw then if it fails then ill use the brinn i have had only 1 saginaw fail in a street stock in the last 10 years

[dirttrackrocker]

Wow..... My head hurts from trying to read that!!!!

You are missing the obvious point. If you have so much saginaw stuff, sell a couple off and use that money to buy a real racing trans. You may not care about your safety, but, what about the guys on the track with you? What happens when you explode a trans and the guy behind you (probably the leader lapping you) takes a piece of it in the chest or through his visor?
Saginaws are getting hard to find and you can get pretty good money for them. Who knows you might even have enough left over to get a copy of Hooked on Phonics.

[JustAddDirt]

wtf

all yo haters are the stupid ones that cant be fixed any way the whole point was to run what i have not trying to be cheep bout it just for someone comeing out and judging someone whit a smart a$$ coment saying if you cant by a raceing trans you shouldent even be raceing had nothing with me not haveing the money for a race tranny i have the money to buy one but the whole point was i already have all the stuff to set it up with a saginaw so there was no money to spent there only turning the tail shaft down and that dident even cost anything and also i dont clame i have 3 cars i know i have them work on them all the time top it all off i realy dont care if i ever get a sponcer anyway most of them want you to do it there way and ive made it this far with out one so ill keep doing it and yea i did buy a brinn tranny tody not because all you hatters and you know what im just gonna let it set on the work bench keep doing what i was doing with the saginaw then if it fails then ill use the brinn i have had only 1 saginaw fail in a street stock in the last 10 years

You are a moron, that needs to go back to english class , and learn proper grammer.
Then go out to shop turn on radio, and put in the brinn tranny and go race safely, but if you build a car like you type on a messege board, you will be lucky to make it to a racetrack.

[dirttrackrocker]

"am i going the right rout with this just keep in mind this is about useing a saginaw so i need info on that part"

Jeff,

This is the last part of his long, run on, single sentence of a post. I know without any punctuation, it's hard to make out a question, but, he did ask if he was going about this the right way, to which a bunch of people including myself answered.

[jsf74]

all yo haters are the stupid ones that cant be fixed any way the whole point was to run what i have not trying to be cheep bout it just for someone comeing out and judging someone whit a smart a$$ coment saying if you cant by a raceing trans you shouldent even be raceing had nothing with me not haveing the money for a race tranny i have the money to buy one but the whole point was i already have all the stuff to set it up with a saginaw so there was no money to spent there only turning the tail shaft down and that dident even cost anything and also i dont clame i have 3 cars i know i have them work on them all the time top it all off i realy dont care if i ever get a sponcer anyway most of them want you to do it there way and ive made it this far with out one so ill keep doing it and yea i did buy a brinn tranny tody not because all you hatters and you know what im just gonna let it set on the work bench keep doing what i was doing with the saginaw then if it fails then ill use the brinn i have had only 1 saginaw fail in a street stock in the last 10 years

Huh??? Engrish pweze

[JHobbs26]

What was it, about 7 years ago when IMCA started to allow aftermarket trannys, until then 90% of mods were running saginaws with mini-clutch setups, and had been for many many years.

Will it work for the OP, yes. Is it as good as running an racing made tranny. No.