Sbc oil pumps?

[stockcar5]

Again Comparing apples to apples here what is your claim to fame and don't cry about the question I asked you LMAO!!!!

Not scared of stockcar5 as he seems to be a blow hard as he can't answer a question that I asked but he can sure cry a lot LMAO.

i never saw where you asked me a question. my bad. i have no claim to fame. i dont own a cnc machine. i did machine a set of brake rotors today. does that make me a machinist now??? LOL!!

let us know how that court thing ends up. you dont have to worry about what you post here. it wont get locked like the posts you reply to on speedtalk!!

[stockcar5]

All jokes aside like or hate carl he answers alof of dart questions on these websites

i'll agree with you there. his cnc machine does a nice job. he's just a douche.

[Ferg58]

jsf74 was asking in general what pump to use. You guys turned this into a pi$$en match. Give your advice and get on down the road.

[CNC BLOCKS]

I have used M55HV in 90 percent of my builds CNC blocks turned it into a pissing match just cause he don't use high volume for the run of the mill racer put the HV in and make sure your pan has at least 7qt capacity so you don't pump it dry and pickup 1/4 to 3/8 off the bottom of the pan and you won't have any issues.

Why do you need 7 quarts that are guys at the local circle track that only can run a stock pan and run HV pumps and no issues for those guys, Suck the pan dry HMMMM where are you going to put 4 or 5 quarts of oil to suck the pan dry. That has been proven many times as myth just check with Mellings as There use to be an announcement on there website in reference to you guys making up stories.

[usafracer]

Wow that esclated quick!!


As for the HP no clue how much. Dyno time to me has never been cheap enough to swap oil pumps. That being said nothing in life is free. You pump more oil it takes HP to do it. Its sience.

[CNC BLOCKS]

i never saw where you asked me a question. my bad. i have no claim to fame. i dont own a cnc machine. i did machine a set of brake rotors today. does that make me a machinist now??? LOL!!

let us know how that court thing ends up. you dont have to worry about what you post here. it wont get locked like the posts you reply to on speedtalk!!

Go to speedtalk and see my accomplishments here are a few about the Chinese Dart look alike block.

http://speedtalk.com/forum/viewtopic.php?t=17747&postdays=0&postorder=asc&start=0

http://speedtalk.com/forum/viewtopic.php?f=1&t=18750

http://speedtalk.com/forum/viewtopic.php?t=18095&postdays=0&postorder=asc&start=0

WHAT ARE SOME OF YOUR MAJOR ACCOMPLISMENTS??????????????????????????????????

You know I have a lot of followers I wish I could post the 3 PM's I got about you LOL. My claim to fame is machining blocks and building engines!!! What do you do for a living???

My engines have won many championships set national and world records!!! Do have any world records????

I ship machined blocks all over the world and have many engine builders and machine shops I deal with everyday.

What is your claim to fame???

You try to be a know-ALL-jest and blow hard just my opinion and a few other see it that way as well LOL.

Again what is your claim to fame !!!!!!

[stockcar5]

Go to speedtalk and see my accomplishments here are a few about the Chinese Dart look alike block.

http://speedtalk.com/forum/viewtopic.php?t=17747&postdays=0&postorder=asc&start=0

http://speedtalk.com/forum/viewtopic.php?f=1&t=18750

http://speedtalk.com/forum/viewtopic.php?t=18095&postdays=0&postorder=asc&start=0

WHAT ARE SOME OF YOUR MAJOR ACCOMPLISMENTS??????????????????????????????????

You know I have a lot of followers I wish I could post the 3 PM's I got about you LOL. My claim to fame is machining blocks and building engines!!! What do you do for a living???

My engines have won many championships set national and world records!!! Do have any world records????

I ship machined blocks all over the world and have many engine builders and machine shops I deal with everyday.

What is your claim to fame???

You try to be a know-ALL-jest and blow hard just my opinion and a few other see it that way as well LOL.

Again what is your claim to fame !!!!!!

like i said a few posts above. i have no claim to fame. nobody has made a fake website about me. im not that famous...LOL!

[CNC BLOCKS]

like i said a few posts above. i have no claim to fame. nobody has made a fake website about me. im not that famous...LOL!

You must be a Wall mart greeter LOL.

[CNC BLOCKS]

Why would you not run a 7qt pan what r u trying to prove? Go ahead run 5qts maybe someday my engines will meet yours on the track and we will see who is better sir. I am just trying to answer the guys question but since you don't agree he has not been able to get a good answer.

Reread my post the track only allows a stock pan so why would you want to get thrown out for being illegal ????

[CNC BLOCKS]

Why would you not run a 7qt pan what r u trying to prove? Go ahead run 5qts maybe someday my engines will meet yours on the track and we will see who is better sir. I am just trying to answer the guys question but since you don't agree he has not been able to get a good answer.

Reread my post the track only allows a stock pan so why would you want to get thrown out for being illegal ????

I have sure won a lot of championships over the years and stilling winning. What is your claim to fame and what shop do you own where you build engines??? Bring it on!!

Go over my F/B page

https://www.facebook.com/cncblocks.northeast

[CNC BLOCKS]

You are literally to much of a jack*** to deal with if you are as good as you claim how come Roush/Yates, Hendricks or Tony Stewart Racing hasn't picked you up? Big deal you can CNC a block can you do anything else? I can do any operation in my shop within .0002" that includes grinding crankshaft, line boring blocks , sizing connecting rods, honing cylinders fitting guides and valve jobs. But according to you, you are the only one in the whole world who can build a good engine just because you can CNC. Well let me tell you something a good machinist is innovative and can come up with many different ideas and will figure out what is best. Also at times he will admit that he does not know everything and is not afraid to pick the phone up and call classy engine builder unlike yourself. A true machinist can do good work without a computer. Since you have a CNC why don't you build your own (not a nice word)(not a nice word)(not a nice word)(not a nice word) oil pump so then the whole nation will know who you are cuz I haven't heard of you until this forum. I am finished with you sir, I apologize to the individual that wanted a question answered as this was the true purpose of this forum!!!!

Let see I did spend some time at DEI years ago as they wanted me to go to work for them, I spent quite a bit of time in the shop going over what was going on,

Let see I have shipped 3 blocks to Hendricks Motorsports for engine builders that work there that build engines on the side.

Again go over my Face Book page, There are a lot of pics of some of what I do for a living. Just scroll down https://www.facebook.com/cncblocks.northeast

I can build a good engine no doubt and being able to do the work in a CNC machine give me an advantage over those who don't have a CNC machine.

Lets see If Hendrick's HAAS CNC machines are good enough for them then MY HAAS CNC machine should be good enough for me.

You only work to .0002 HMMMMM

So what machine shop do you own?? ANY PICS of what you do or are bull shyting everyone here LOL.

This is 2013 CNC machining is the way to go believe me again its 2013

What do you machine with and hone with??? Like to see some pics!!!!!

Like I said I have my engines have set national records and world records and what have you done?????????????????????????????????????????????? ?

You should use profanity on this site !!!! Your showing how much of a moron you are LMAO.

[dereksehi]

Stock car driver I have cars that run Boone County Raceway, US30 and Riviera Raceway in Norfolk which is where I run a Northern Sportmod weekly always have several that go to spring and fall nationals and a few that make the pull to Boone for the SuperNats. I also have engines turning circles in Utah,Louisiana and Missourri. I have watched you run in Albion and put on a good show should you be there some night I am running I will come introduce myself.

[dereksehi]

The track is goin to be under new management this year so hopefully it will be even better!!

[let-r-eat]

Why would a stock pan engine with a 400hp build ever need anymore than what came stock?

[CNC BLOCKS]

You are literally to much of a jack*** to deal with if you are as good as you claim how come Roush/Yates, Hendricks or Tony Stewart Racing hasn't picked you up? Big deal you can CNC a block can you do anything else? I can do any operation in my shop within .0002" that includes grinding crankshaft, line boring blocks , sizing connecting rods, honing cylinders fitting guides and valve jobs. But according to you, you are the only one in the whole world who can build a good engine just because you can CNC. Well let me tell you something a good machinist is innovative and can come up with many different ideas and will figure out what is best. Also at times he will admit that he does not know everything and is not afraid to pick the phone up and call classy engine builder unlike yourself. A true machinist can do good work without a computer. Since you have a CNC why don't you build your own (not a nice word)(not a nice word)(not a nice word)(not a nice word) oil pump so then the whole nation will know who you are cuz I haven't heard of you until this forum. I am finished with you sir, I apologize to the individual that wanted a question answered as this was the true purpose of this forum!!!!

I got an email last nite from some one who saw this post and we both have a few questions for you as this guy that sent me the email I am sure uses a CNC machine as well.

You just told me how good your lets find out!!!! But you say you work with in .0002 HMMMMMM

First of all how do you bore your cylinders to blue print??? Please don't tell me your just throwing a boring bar on the decks and boring the cylinders and calling that blue print. Please post pics of your operation??? But you say you work with in .0002 HMMMMMM

How are you enlarging your lifter bores?? Please don't tell me your using fixturing!!! Its 2013 now !! But you say you work with in .0002 HMMMMMM

Here is a link on a guy that took his block I had machined and it ran fine till he thought he was working magic with his BHJ fixture and cost this guy a lot of money and now its not running the times it was before. I would say the seat timing events are not the same now compared to what I did and being a roller cam lifter bore placement is critical. Please post some pics???? But you say you work with in .0002 HMMMMMM

http://www.yellowbullet.com/forum/showthread.php?t=594824

What are you using to blue pint bore the cam tunnels??? Please don't tell me you having nothing to blue print with but you say you work with is .0002 HMMMMMM

Even chamfering the top of the cylinders every block I did the chamfer is exactly the same, Please don't tell me your chamfering the top of the cylinders by hand!!!! But you say you work with in .0002 HMMMMMM

Here is a little of what I do for blue printing a block. Could you post pics of what you do as you told me how good you are remember (But you say you work with in .0002 HMMMMMM)

http://www.chevelles.com/forums/showthread.php?t=93124