Thanks Dynoman!

[Egoracing]

HA, Shows how full of $hit you really are, I have never EVER even sold an engine part on E bay. If you are going to try to insult someone get your facts straight and know who you are talking about. Now if you want to keep going I am sure my attorney would be REALLY interested in what you have to say.

[TeamGRT12x]

Ever notice as soon as someone talks about ordering parts, he is backed up 2-3 weeks?

[chrish]

dynoman sold me stale cookies!!!

Ive yet to use the treated spings he sold me 3 yrs ago but i do know for a fact that his springs tested best above all during turkey 100 tech and the team he helped ran a strong 3rd.

[50j]

Dyno, you do not step the jet size up 8 to 10 sizes when going from Sunoco Standard 110 to oxygenated fuel including the Green E15. You do go up but not quite that much and darn sure not 12 sizes. YOU obviously don't know anything about carbs. Should we re-visit the 350 cfm 4412, the two stage power valves in 3310's to make up for yanking the secondary side open with a sheet metal screw, using 2 times more fuel with E-85 than with gas, the Dorton 4412 metering blocks with adjustable bleeds, and more? You're struggling.

[50j]

Also, they used the 830 carbs to match the restrictor plate but use a large venturi and your hp numbers are way off.

[stockcar5]

Oil Filters:
As for the folks that wanted to try mine, I am not selling them anymore. I think you can buy the from a company in California for $49.95 ea. they market them for Offshore Boats and state a gain of 40HP on 800hp BBCs, they purchased my last run of 10,000 filters and purchased the rights to make them exclusively for their boat business. I signed a 5 year non-compete / non-disclose so you'll have to find them on your own. You can also try John Jomars filter it is pretty close and not too much cash.

Posted on 8-13-12

They ran 3rd with Treated GM Springs, Plugs, Oil and Filter ( Power-Pack Special +25RWHP ).

LOL

[dynoman14]

Crish H,
You say you have had the springs for 3 years and never used them, WHY?

I will gladly re-treat them and re-rate them for you. Since we texted over the weekend regarding mufflers on Franks' crate engine why didn't you just tell me then? You can text me for shipping address and I will get them in the re-treat program and have them ready for you in 21 days.

3 Years ago Royce Bray and Kenny Harriss ran them on the way to a Fastrak Championship.

I re-treat Bobby Daudermans springs after every 5 races and all of the German steel has been holding for about 3 years now. The current material is not doing as well only lasting 1-2 treats on the intake and then I rotate them to exhaust for one or two cycles.

If you rate my treated springs on a Rimac they will be 5-10# dpwn on pressure at 1.870" but if you run them on a Valve spring dyno or Spintron you will see they are stable without harmonics and resonance up to 7200rpms.

I have had a couple folks running them at Dixie and Rome for a while and they are plenty happy with the results.

Since you are probably a customer of Lamar Hunts you need to ask him about Bobby Turners flat tappet steel head engine that got torn down about 5 times back about 20 years agp on the way to about 18 wins and 4 or 5 Bounty wins until a little deal with Bill Ingram netted them a bounty split....We were running roller springs on welded stellite cams and stellite lifters and turning 9500. Replaced springs every 2 weeks and never had a failure in 2 years of running the engine. Current springs are better but the old stellite cams are stilll kicking butt in NLMS and Limiteds running around the SE.

[TeamGRT12x]

Crish H,
You say you have had the springs for 3 years and never used them, WHY?

I will gladly re-treat them and re-rate them for you. Since we texted over the weekend regarding mufflers on Franks' crate engine why didn't you just tell me then? You can text me for shipping address and I will get them in the re-treat program and have them ready for you in 21 days.

3 Years ago Royce Bray and Kenny Harriss ran them on the way to a Fastrak Championship.

I re-treat Bobby Daudermans springs after every 5 races and all of the German steel has been holding for about 3 years now. The current material is not doing as well only lasting 1-2 treats on the intake and then I rotate them to exhaust for one or two cycles.

If you rate my treated springs on a Rimac they will be 5-10# dpwn on pressure at 1.870" but if you run them on a Valve spring dyno or Spintron you will see they are stable without harmonics and resonance up to 7200rpms.

I have had a couple folks running them at Dixie and Rome for a while and they are plenty happy with the results.

Since you are probably a customer of Lamar Hunts you need to ask him about Bobby Turners flat tappet steel head engine that got torn down about 5 times back about 20 years agp on the way to about 18 wins and 4 or 5 Bounty wins until a little deal with Bill Ingram netted them a bounty split....We were running roller springs on welded stellite cams and stellite lifters and turning 9500. Replaced springs every 2 weeks and never had a failure in 2 years of running the engine. Current springs are better but the old stellite cams are stilll kicking butt in NLMS and Limiteds running around the SE.

I had a buddy that I washed his car for him and treated the body with the car wash wax. After that he ran the car three nights without washing it and the dust just flew right off. Why didn't he just telegraph me to tell me he hasn't washed the car since then? Since he is a customer of Wal Mart, he should ask the guy he bought the string cheese from about his sisters cousins brothers new pontoon that I sold him a propeller for. On the dyno it made 500 more HP at the blades. Maybe you can wrap your head around the idea of three valve springs per valve. I am afraid the irish steel that we are using on the blades require us to re wash my buddies race car every week.

[dynoman14]

ego,
Sorry to have mistaken you for another 4m'er that is an engine builder that posted his link to that engine on e-bay, you are just the expert on everything else.

http://www.ebay.com/itm/All-Aluminum..._Parts&vxp=mtr

GRT,
I do not own an engine dyno currently but I do use a couple locally as well as in Charlotte. They all crank out about the same numbers on crates so it is not my dyno that is generating the numbers I discuss.

I have been under construction building an inertia engine dyno for the last 5 years and I am getting pretty close to completion. Another $15-20K and 100+ hours and I should be about done. I have tested the dyno on some small engines up to 50hp and everything is fine with data gathering, hi-rate sampling and cylinder to cylinder pick-ups. I have 2 cylinders good to 6000rpms and need to get additional channels and programming for 8 cylinders and 10,000rpms.

As you were discussing in your post you should probably stick to washing cars as that looks to be your calling.

Most you morons like stockcar5 can't read...
Like I said in my first post...they ran my stuff, they did not purchase it. Is that a concept you can understand or do I need to explain it further ???

I don't think what I said in that post a couple months ago was in-accurate. I am not currently selling the filter that I sold to the offshore boat guy. I have a non-compete / non-disclosure agreement on that filter and its construction. I do however have 4 other proprietary filters designs and have the ability to manufacture and market when I chose to do so.

Kind of like last year when I said I don't certify Crate engines, but I do build them and get them certified by other Certified Crate Engine Builders.

50J,

Only thing I am struggling to do is to keep up with all of the BS you post on here regarding my old posts...

To address each one of your quotes of mine;
I posted the 350cfm #4412 as a typo and I re-posted a correction of that, you ever make a mistake??? I have built and sold a couple hundred of each of those carbs thru my QuickCarb program with QuickCar Racing Products out of Winder, GA in the late 1990's.

I have been using a screw in the throttle arm for about 20 years as it is a way of working in the grey area of the rules regarding mechanical activation of vacuum secondary carbs. I also use 2 stage power valves in the secondary when allowed to augment the early opening of the secondaries while keeping the secondary jet balanced with the front jets.

Dorton HP 500 carbs do have adjustable air bleeds in the choke area and the metering blocks.

As far as green race gas I was referring to a SuperBike fuel that comes out of CT and CA at no point did I ever call it Green 15 or whatever you are referring to.

As I have said 100 times in the past, my jet numbers apply to my carburetors. Since I use much smaller jet wells, smaller but more jet well bleeds and air bleeds it takes a bigger jet size to increase the fuel mass in comparison to a standard holley. If you monitor fuel flow by mass you will easily follow the increase in fuel mass as it relates to power increases.

In my book when a fuel has 1/2 the BTU's it requires twice the volume to make the same power as an equivalent fuel with double the BTU's. Much like the comparison between e-85 and most race fuels. I know there are plenty of folks that try and make power with the lean end of the curve but any good alcohol engine builder will tune to the fat end of the stoichiometric curve.


Thanks for hijacking this thread and keeping it up top, like I have said before the more you guys rag on me the more folks I have e-mailing and pm'ing me about my products.

Thanks Y'all

[stockcar5]

Thanks for hijacking this thread and keeping it up top, like I have said before the more you guys rag on me the more folks I have e-mailing and pm'ing me about my products.

This aint no "highjack"! After Bobby D slipped his willy out of your cornhole you asked him politely for some free advertisement! You knew what would happen. You're an attention whore, thats why you're here.

[50j]

ego,
Sorry to have mistaken you for another 4m'er that is an engine builder that posted his link to that engine on e-bay, you are just the expert on everything else.

http://www.ebay.com/itm/All-Aluminum..._Parts&vxp=mtr

GRT,
I do not own an engine dyno currently but I do use a couple locally as well as in Charlotte. They all crank out about the same numbers on crates so it is not my dyno that is generating the numbers I discuss.

I have been under construction building an inertia engine dyno for the last 5 years and I am getting pretty close to completion. Another $15-20K and 100+ hours and I should be about done. I have tested the dyno on some small engines up to 50hp and everything is fine with data gathering, hi-rate sampling and cylinder to cylinder pick-ups. I have 2 cylinders good to 6000rpms and need to get additional channels and programming for 8 cylinders and 10,000rpms.

As you were discussing in your post you should probably stick to washing cars as that looks to be your calling.

Most you morons like stockcar5 can't read...
Like I said in my first post...they ran my stuff, they did not purchase it. Is that a concept you can understand or do I need to explain it further ???

I don't think what I said in that post a couple months ago was in-accurate. I am not currently selling the filter that I sold to the offshore boat guy. I have a non-compete / non-disclosure agreement on that filter and its construction. I do however have 4 other proprietary filters designs and have the ability to manufacture and market when I chose to do so.

Kind of like last year when I said I don't certify Crate engines, but I do build them and get them certified by other Certified Crate Engine Builders.

50J,

Only thing I am struggling to do is to keep up with all of the BS you post on here regarding my old posts...

To address each one of your quotes of mine;
I posted the 350cfm #4412 as a typo and I re-posted a correction of that, you ever make a mistake??? I have built and sold a couple hundred of each of those carbs thru my QuickCarb program with QuickCar Racing Products out of Winder, GA in the late 1990's.

I have been using a screw in the throttle arm for about 20 years as it is a way of working in the grey area of the rules regarding mechanical activation of vacuum secondary carbs. I also use 2 stage power valves in the secondary when allowed to augment the early opening of the secondaries while keeping the secondary jet balanced with the front jets.

Dorton HP 500 carbs do have adjustable air bleeds in the choke area and the metering blocks.

As far as green race gas I was referring to a SuperBike fuel that comes out of CT and CA at no point did I ever call it Green 15 or whatever you are referring to.

As I have said 100 times in the past, my jet numbers apply to my carburetors. Since I use much smaller jet wells, smaller but more jet well bleeds and air bleeds it takes a bigger jet size to increase the fuel mass in comparison to a standard holley. If you monitor fuel flow by mass you will easily follow the increase in fuel mass as it relates to power increases.

In my book when a fuel has 1/2 the BTU's it requires twice the volume to make the same power as an equivalent fuel with double the BTU's. Much like the comparison between e-85 and most race fuels. I know there are plenty of folks that try and make power with the lean end of the curve but any good alcohol engine builder will tune to the fat end of the stoichiometric curve.


Thanks for hijacking this thread and keeping it up top, like I have said before the more you guys rag on me the more folks I have e-mailing and pm'ing me about my products.

Thanks Y'all

Dorton 500 carbs do not have adjustable bleeds in the metering blocks, the 350 carbs do. E-85 doesn't require twice as much fuel as gas, and any engine builder that has dyno tuned both will know that. It's o.k. though, whatever you want to say. Hopefully people will fact check things before believing them, and you'll be the one to deal with your customers. It's unfortunate that people will be confused by inaccurate b.s. plastered on here. Good luck.

[stockcar5]

I am afraid the irish steel that we are using on the blades require us to re wash my buddies race car every week.

You Iowa boys need to step into the 21st century. I've been on a proprietary Bolivian spring sprinkled with 11 herbs and spices for years. Do i need to explain it to you for you to understand? Maybe you should ask one of my best friends Parnelli Jones what he thinks of my laydown turds. If big E were still with us he could tell ya'll a story or 2 about my shiznit!

[50j]

Big E! LMAO. That would be something to see.

[TeamGRT12x]

I have a special blend of titanium/uranium that's nuclear ready to go into this new Dodge 80 cylinder small block that is similar to what Brad Keselowski won the championship with. I don't sell parts, but people run them. I don't build engines, but I have them certified. Anyone care to tell us how you run 5 rods per cylinder and still have a BFSCMEHSKDI of 200 square meters?

I just got off the phone with Big E. He's been at my shop numerous times to get parts for his ex wifes stepsons pit bike. I have been working on a new transmission that uses no gears or anything inside. I have been testing this at the salt flats with good success. You should talk to your buddy Billy Ray Rectum over there Mark. He bought ten of these designs. I also am getting ready to release a new set of super spectrum tear offs that add 30 RWHP. I just got back from a trip to the scrap yard, if you take the right gaskets off of the old DOHC 2.4 GM engines you can use them on the small block Ford. I have a device I make that makes them into SBC gaskets, since they are running low on supply.

I have plenty of these parts, but if anyone wants one it will be a four year backlog. Sorry.

[TeamGRT12x]

50j,
Once again your genius shines, maybe you should be checking the differences between Oxygenated Green Sunoco and Sunoco 110, it has similarities to most like VP or others and the jet differences are usually 8-10.

Uh, so you're not talking about the Sunoco Green here then?